Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
Classe’s Controller Area Network, or CAN-Bus, opens the way to a new level of interaction between our Delta range of amplifiers, preamps, processors and source components. When the SSP-800 is connected with CAN-Bus, the different elements of a Delta series system are in constant communication, creating a “global” network that delivers system wide status information and shared operational features, all through the touchscreen display. CAN-Bus will allow a single Delta series touchscreen to: • Display status information for every connected unit, including amplifi ers which do not have a touchscreen display. • Create a “PlayLink” that allows an SSP or Preamp to automatically switch to the correct input when a Delta series source component starts playback. • Adjust the global system brightness. • Configure the entire system to go in and out of standby at the touch of a button and also bring individual components in and out of standby. • Mute any connected unit. hardware setup 1 Classe Delta Series Products Two or more Classe Delta series products are required, at least one of which must have a touchscreen display. 2 Category 5 Network Cables These are ordinary network cables, commonly used for broadband Internet connections. They should be typical “straight through” cables not the “crossed over” type, and the total required will be one less than the total number of Delta series components in your system. 3 CAN-Bus Terminator At minimum, a single CAN-Bus Terminator will be required. It is inserted into the CAN-Bus OUT connector of the last component in the CAN-Bus daisy chain. One is included in the box with your SSP-800. They are also available free of charge from your nearest Classe Customer Support Centre 4 SSP-300 & 600 CAN-Bus Interface Box Systems that include an SSP-600 or SSP-300 will also require an SSP-300/600 CAN-Bus Interface Box. These are included with the products or available free of charge from your nearest Classe Customer Support Centre The diagrams below illustrate how to connect the CAN-Bus hardware. Any combination of models in any order without SSP-300 or SSP-600. Any combination of models in any order with SSP-300 or SSP-600. NOTE: Daisy chain must be terminated with CAN-Bus Terminator. OUT CAN BUS IN OUT CAN BUS IN OUT CAN BUS IN OUT CAN BUS IN OUT CAN BUS IN OUT CAN BUS IN OUT CAN BUS IN OUT CAN BUS IN using CAN-Bus CAN-Bus is controlled via the touchscreen of any Delta series component. Th ere is no master component, so Delta series systems where two or more units have a touchscreen can be controlled through any of the touchscreens. However, it is probably easiest to start using CAN-Bus through just one. CAN-Bus is accessed by pressing the menu button on the face of the unit or remote, then the status button, followed by the more button. The touchscreen will then display the CAN-Bus devices screen, which lists connected Delta series components by model & serial number. Highlighting a unit on the CAN-Bus devices screen identifies it as the target unit. The front panel LEDs of the target unit will start flashing (unless you highlight the unit that you are using to access CAN-Bus). Once you have chosen the target unit press select. The target unit’s LEDs will stop flashing and the touch screen will list the CAN-Bus features available to it. Some CAN-Bus features are shared by all models, some are specific to individual models. CAN-Bus shared features configuration operate AC status status The following CAN-Bus features are shared by all models. Selecting confi guration will present the CAN-Bus confi guration screen allowing access to name, global brightness, and global standby features.. • name enables you to set the name that this component will be listed under in the CAN-Bus devices screen. The name will appear next to the unit model and serial number, and facilitate the identification of units in large systems. • global brightness enables you to adjust the touchscreen and LED brightness of all the components in your system by changing the brightness of a single touchscreen. All CAN-Bus software updates automatically set the updated unit to global brightness. If you want a particular unit to be excluded from global brightness, deselect global brightness for that unit. • global standby enables you to bring your entire system in and out of standby by pressing the standby button of any unit or remote. All CAN-Bus software updates automatically set the updated unit to global standby. If you want a particular unit to be excluded from global standby, deselect global standby for that unit. Th e operate settings allow you to bring the target unit in and out of standby, or mute. This key will be disabled for the unit whose touchscreen you are using to access CAN-Bus. Th e AC status screen displays information from the target unit’s electrical supply sensors. Two screens are available, with the second acc...