Iniciar sesión:
Votos - 3, Puntuación media: 4 ( )

Manual de usuario Kenwood, modelo KDC-W241

Fabricar: Kenwood
Tamaño del archivo: 590.78 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Otros manuales para este modelo:
Unidad - KDC-W241 (589.74 kb)ru
Unidad - KDC-W241 (580.5 kb)en
Unidad - KDC-W241 (583.67 kb)ru

Resumen del manual


Ignition cable (Red) A-7 Pin (Red) Unit Vehicle A-4 Pin (Yellow) Battery cable (Yellow) . • When the connection is made as in 3 above, the unit’s power will not be linked to the ignition key. For that reason, always make sure to turn off the unit’s power when the ignition is turned off. To link the unit’s power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. English | 17 Installation/Removing the Unit Installation Removing the hard rubber frame Metal mounting strap (commercially available) Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Catch Lock Accessory2 Removal tool 2 When the upper level is removed, remove the lower two locations. . • The frame can be removed from the bottom side in the same manner. . • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Removing the Unit 1 Refer to the section and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Screw (M4X8) (commercially available) Accessory2 ¤ • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. 18 | KDC-W3541/KDC-W3041/KDC-W312/KDC-W241/KDC-241 Troubleshooting Guide Some functions of this unit may be disabled by The messages shown below display your some settings made on this unit. systems condition. ! TOC ERR: • No disc has been loaded in the disc Cannot display the user of System Q. magazine. ^

recorded that the unit can play. (page 10) • (page 4) is not set to On. E-77: The unit is malfunctioning for some reason. . Press the reset button on the unit. If the “E! 77” code does not disappear, consult your • Cannot register a security code. nearest service center. • Cannot set up Display. ^ (page 12) is not E-99: Something is wrong with the disc magazine. turned off. Or the unit is malfunctioning for some reason. . Check the disc magazine. And then press the reset button on the unit. If the “E-99” What might seem to be a malfunction in your unit code does not disappear, consult your nearest service center. may just be the result of slight misoperation or miswiring. Before calling service, first check the IN (Blink): The CD player section is not operating following table for possible problems. properly. . Reinsert the CD. If the CD cannot be Tuner source ejected or the display continues to flash even when the CD has been properly ? Radio reception is poor. reinserted, please switch off the power . The car antenna is not extended. and consult your nearest service center. . Pull the antenna out all the way. PROTECT: The speaker wire has a short-circuit or Disc source touches the chassis of the vehicle, and then the protection function is activated. ? The specified disc does not play, but another one . Wire or insulate the speaker cable plays instead. properly and press the reset button. If . The specified CD is quite dirty. the “PROTECT” code does not disappear, . Clean the CD. consult your nearest service center. . The disc is loaded in a different slot from that specified. NA FILE: An Audio file is played with a format that this . Eject the disc magazine and check the number unit can’t support. for the specified disc. . ---. The disc is severely scratched. COPY PRO: A copy-protected file is played. . Try another disc instead. . --- Audio file source ? The sound skips when an Audio file is being played. . The media is scratched or dirty. . Clean the media, referring to the CD cleaning of the section on (page 3). . The recording condition is bad. . Record the media again or use another media. English | 19 Specifi cations FM tuner section Frequency range (50 kHz space) : 87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 26dB) : 0.7 .V/75 . Quieting Sensitivity (S/N = 46dB) : 1.6 .V/75 . Frequency response (±3.0 dB) : 30 Hz – 15 kHz Signal to Noise ratio (MONO) : 65 dB Selectivity (DIN) (±400 kHz) : . 80 dB Stereo separation (1 kHz) : 35 dB MW tuner section ...

Otros modelos de este manual:
Unidad - KDC-241 (590.78 kb)
Unidad - KDC-W3041 (590.78 kb)
Unidad - KDC-W312 (590.78 kb)
Unidad - KDC-W3541 (590.78 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría