Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Hint: Assembling the track is not a one-time assembly. The track has been designed for easy disassembly for storage (see Storage and Care section). Tab 4 Slot Tab Slot Symbols Track Layout and Assembly o cho o o o c h oo choo o chugga chug chug chug c h ugga ch ug chug chug • 74878b-0920.qrk 6/19/01 10:48 AM Page 4 Tunnel Top, Hooked Tabs, Slots, Tunnel 4 • Apply the label to the tunnel, as indicated in the illustration. • Insert and “snap” the four hooked tabs on the tunnel top into the four slots in the tunnel track. Pull up on the tunnel top to be sure it is secure. Note: This is a one-time assembly. Tunnel Top Hooked Tabs Slots t o ot to o t • t oot toot toot toot • toot toot t oo t t oo t • to ot toot toot to 5 2 • Apply the labels to the station, as indicated in the illustration. • Insert and “snap” the hooked tabs on the station into the slots in the track. 1 3 • Apply the label to the barn, as indicated in the illustration. • Insert and “snap” the hooked tab on the barn into the slot in the track. • Fit the posts on the fence into the holes in the track. Holes Plug Hooked Tab Hooked Tab Station Slot Slot Railroad Crossing Slot Barn Hooked Tab Slot Fence Posts Accessory Assembly Hint: Apply the labels as shown in the following illustrations. For best results, wash your hands before applying the labels and make sure the areas to which the labels will be applied are clean and dry. Avoid repositioning a label once it has been applied. • Apply the labels to the railroad crossing, as indicated in the illustration. • Fit the railroad crossing plug into the slot in the track. o choo ch oo ch oo c hoo 74878b-0920.qrk 6/19/01 10:48 AM Page 5 5 • Apply the label to the loader, as indicated in the illustration. • Insert and “snap” the two hooked tabs on the loader into the two slots in the track. Pull up on the loader to be sure it is secure. Ready when you are! IMPORTANT! For best performance, always point the microphone toward the engine. Make sure the microphone is no more than eight feet from the engine. Engine Caboose Loader Car 6 Loader Accessory Assembly Power Switch Hooked Tab Slot • Slide the power switch on the engine to the “on” position. • Hook the loader car to the engine. • Hook the caboose to the loader car. c h u g c hugga chug chug chug • toot toot • toot t o ot 74878b-0920.qrk 6/19/01 10:48 AM Page 6 toot toot • toot toot toot toot • toot toot toot toot • toot toot toot chugga c h ug ga c h ug g a • chugga chugga c • Place the train cars on the track. Hint: You can also place the train cars off the track, on another hard, flat surface for more “off-road” fun! • Press the smoke stack for ready mode. Toots the Train™ is waiting for your command! • While pressing the bar on the microphone, tell Toots the Train™ to go. You say, “Go!” Hint: If you do not tell the train to go, Toots the Train™ will remind you three times! • Toots the Train™ will go around the track approximately three times and then stop. • You can either: - Press the bar on the microphone and say, “Go!” - Or, press a destination on the microphone base. Then, press the bar on the microphone and say, “Go!” Hint: If you do not tell the train to go after the last reminder, Toots the Train™ will automatically shut off after 30 seconds. To put Toots the Train™ back to ready mode, simply press the smoke stack again. • To stop the train at any time, simply press the bar on the microphone and tell Toots the Train™ to stop. You say, “Stop!” • To shut power completely off, slide the power switch on the engine to the ”off ” position. Bar Button • For off-road fun, take Toots the Train™ off the track and place onto a hard, flat surface. Hint: For best performance, do not use outdoors. • Press the bar on the microphone and tell Toots the Train™ to go. You say, “Go!” Hint: Toots the Train™ only moves straight ahead. There is no remote steering. 7 All Aboard! • Press the button on top of the engine for different sound effects or music – “Toot - Toot!” Hint: See pages 10 and 11 for some words to the music! Microphone Smoke Stack t t oot toot 74878b-0920.qrk 6/19/01 10:48 AM Page 7 • Press the Station destination button on the microphone base. • While pressing the bar on the microphone, tell Toots the Train™ to go. You say, “Go!” We’re Going to the Station • Press the Tunnel destination button on the microphone base. • While pressing the bar on the microphone, tell Toots the Train™ to go. You say, “Go!” • Place the coal boulder on top of the tunnel. Press the detonator to blast the boulder into the loader car. 8 Hello Tunnel Detonator Tunnel Destination Button mo o o o • moo b aa a b aa a b aa a • cluck cluck cluck cluck • moo o o m o o Station Destination Button • Press the Loader destination button on the microphone base. • While pressing the bar on the microphone, tell Toots the Train™ to go. You say, “Go!” • Place a bale of hay on top of the loader. Turn the crank on the side of the loader to drop the bale of hay into the loader car. Here’s the ...