Siehe Bild 5. 8. Die Schrauben (J) durch das Unterteil des Wagens und die Befestigungsbeschläge anbringen. Sicherungsscheiben (K) und Muttern (L) montieren. Nur diese leicht anziehen (die Schrauben werden von der Innenseite des Wagens montiert). Siehe Bild 5. 9. Die Beschläge (S) an die Rückwand montieren, so daß die Bohrungen parallel zur Rückwandverstärkung und den Wagenseiten laufen. Siehe Bild 5 zur genaueren Information. 10. Mit 6 Sechskantschrauben (F), Sicherungsscheiben (H) und Mutter

(B) Use the rear wheel depth/stability control knob to set the rear wheels for extra stability. This can be a great benefit when you do choose to run the aerator across a hill. An added benefit of using the rear wheel depth control when aerating across a hill is that you will improve the consistency of the cores pulled from the uphill tines when compared to those pulled by the downhill tines. (C) Removing the downhill weight reduces roll-over risk and maintains consistent core plug length. (See

3 Edger-Trimmer Features ...................... 4 Assembly............................................... 5 Attaching the Handle.............................. 5 Installing Throttle Wire............................ 5 Fill Engine With Oil................................. 5 Operating Your Edger- Trimmer ..................................................6 Correct Engine Operation....................... 6 Fuel Specication ................................... 5 Oil Specication..........................

Model LE389 Read and keep this book for future reference. This book contains important information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. PRODUCT INFORMATION The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to make sure state laws and other laws are followed. 4.2006 MS-3616MA Congratulations... Thank you for purchasing this qu

8 16. Assemble axle and drawbar tongue to wheel support keeping open side of tongue facing down. Fasten axle to wheel support or axle brackets, using 1/4"x11/2" (6 x 40mm) long hex bolts (G) lock washers (H) and hex nuts (I). See figure 11. CAUTION! It may be necessary to block cart in upright position to prevent tipping when installing wheels. 10 17. Assemble large diameter flat washer (B), wheel, another flat washer (B), cotter key (A) and hub cap (C) to each axle end. N.B. Position valve

See figure 4. 6. Assemble wheel support to cart with eight slotted head screws (J), lock washers (K) and hex nuts (L). See figure 4. Heads of screws go to the inside of cart and should be tightened at this time. 7. Position the tailgate reinforcement bracket (Z) over end of cart. See figure 5. 8. Start slotted screws (J) through bottom of cart (heads of screws to the inside of cart) and reinforcement bracket. Secure finger tight with hex nuts (L) and lock washers (K). See figure 5. 9. Positi

960 73 00-03 54 Inch Mower Grass Catcher 03056 SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent ac- cidental starting when setting up, transporting, ad justing or making re- pairs, al ways dis connect spark plug wire and place wire where it can not contact spark plug. WARNI

NOTE: Handle carefully so as not to damage full bag in dicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. LEVEL MOWER DECK Be sure deck is properly leveled for best mower per for - mance. See your tractors owner's manual for instructions. 6 COVER UPPER CHUTE FIG. 5A HANDLE FULL BAG INDICATOR LOWER CHUTE BOSSES

Vea si hay obstaculos que puedan dificultar un desplazamiento imprevisto (raices, piedras, ramas, agujeros, zanjas, etc.). Proceda con sumo cuidado al trabajar en pendientes. 4. Para desplazar la maquina debe pararse el motor. 5. No apoye nunca la maquina con el motor en marcha sin tenerla bajo control. Espanol – 21 INSTRUCCIONES DE SEGURIDAD Tecnica basica de trabajo Instrucciones de seguridad durante el trabajo • Debe tener siempre una posicion de trabajo segura y firme. • Utilice siempre las