Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 2   Tamaño del archivo: 40 kb   Fabricar: MTD  
Categoría: cortadoras de césped

Descargado: 0   Tamaño del archivo: 1 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

2. This machine is a precision piece of power equipment, not a plaything. Therefore, exercise extreme caution at all times. Your unit has been designed to perform one job: to edge lawn. Do not use it for any other purpose. 3. Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the instructions in this manual and should be trained and supervised by a parent. Only responsible individuals who are familiar with these rules of saf

Descargado: 4   Tamaño del archivo: 64 kb   Fabricar: MTD  
Categoría: cortadoras de césped

Descargado: 1   Tamaño del archivo: 134 kb   Fabricar: MTD  
Categoría: cortadoras de césped

Descargado: 7   Tamaño del archivo: 2 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. PRINTED IN U.S.A READ SAFETY RULES AND

Descargado: 3   Tamaño del archivo: 1 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

See figure 3. FRONT WHEEL BELLEVILLE WASHER (B) HEX NUT, (D) 5. Assemble the front wheel (O) toward the inside of the unit as shown in figure 4. Place shoulder bolt (A) through wheel, then belleville washer (B) (between wheel and frame, cupped side against the frame). Secure with lock washer (C) and hex nut (D). See figure 4. FIGURE 4. 6. Assemble the upper handle (R) to lower handle. Place the head of carriage bolts (E)to the outside of handle. Secure with lock washers (F) and and hex nu

Descargado: 3   Tamaño del archivo: 1 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

See figure 6. FIGURE 6 5 I A B c 7A p ¥ ^0 V V7 Screw FIGURE 7 HEX LOCK NUT (R) HEX BOLT (S) / / / ADJUSTMENT BRACKET FIGURE 8 8. Assemble the throttle control to the handle panel as follows. A. Hold the throttle control assembly beneath the handle panel. Turn the control sideways and insert the lever up through the wide portion of the slot on the handle panel. See figure 7A. B. After the end of the lever is through the slot, turn and then tip the control forward as shown in fi

Descargado: 3   Tamaño del archivo: 1 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

Then place axle through one wheel so the hub of the wheel is to the outside of the unit. Next place axle through spacer (D), the other wheel (hub to the outside of the unit) and through second support arm. See figure 4. Secure with push cap (E) by tapping it on with a hammer. See figure 5. It is necessary to hold a block of wood or a second hammer against the push cap on the other side of the axle. 5. Secure the front wheels and axle in position using two hairpin cotters (A). See figure 5. 6.

Descargado: 0   Tamaño del archivo: 1 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

Refer to figure 10. FIGURE 12 I BLADE PLANE ADJUSTMENT The cutting blade can be adjusted to eight positions from vertical to horizontal. To adjust, release tie adjustment lever on the pivot bracket and rotate ihe spindle housing. Place adjustment lever in nolch desired. See figure 13. When the blade is adjusted toward the horizontal position, the front wheels must also be adjusted. Remove the two hairpin cotters and slide the spacer and wheel to the right as shown in figure 14. Reinsert the

Descargado: 0   Tamaño del archivo: 1 mb   Fabricar: MTD  
Categoría: cortadoras de césped
@name

Keep clear of the discharge opening at all times as the rotating blade can cause injury. 4. Stop the blade when crossing gravel drives, walks or roads. 5. After striking a foreign object, stop the engine, remove the wire from the spark plug, and thoroughly inspect the edger for any damage. Repair the damage before restarting and operating the edger. 6. If the equipment should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of





Categoría