Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
To mark a waypoint: 1. Press in and hold the THUMB STICK for two seconds to display the Mark Waypoint Page. Your current location is marked as a waypoint and automatically assigned a three digit number. 2. The ‘OK’ button is highlighted so press the THUMB STICK to save the To move about with the Map Page: 1. Use the PAGE button to access the Map Page and view the new waypoint. Press the ZOOM IN button to get a more detailed view of the map. 2. Walk or drive around for a few minutes, make a right or left turn, then continue for a few more minutes and then stop. The ‘position icon’ shows your location and the dotted line shows your path of travel (a Track). Position Icon showing your current location Track Line The newly marked Waypoint To return to a waypoint using Goto: 1. Press the FIND button to display the Find Menu. 2. Use the THUMB STICK to highlight ‘Waypoints’ and then press it in. 3. Use the THUMB STICK to highlight ‘Nearest’ and then press it in. 4. Use the THUMB STICK to highlight the waypoint and then press it in to display the Information Page. 5. With the on-screen ‘Goto’ button highlighted, press the THUMB STICK to activate the Goto navigation feature. Waypoints List Find Menu Waypoint Information Page Returning to a Waypoint with a Goto To finish your return: 1. The Navigation Page displays the ‘Bearing Pointer’ indicating the direction to go. Because you can’t always travel in a straight line, refer to the Bearing Pointer from time to time. As you move and whenever possible, turn in the direction the Bearing Pointer directs. 2. Use the PAGE button to move to the Map Page to see your location marked by the Position Icon and a straight dark line leading to the waypoint. Move back and forth between the Map Page and the Navigation page to check your progress and verify your bearing. 3. To stop navigating, highlight the Options Menu button on either page, press the THUMB STICK, select ‘Stop Navigation’, and then press the THUMB STICK. Options Menu Button A Goto on the Navigation Page Map Page on a Map Page Options Goto Menu © Copyright 2005 GARMIN Ltd. or its subsidiaries Part Number: 190-00234-01 Rev. C Printed in Taiwan LEGEND QUICK START GUIDE Internal GPS Antenna Waterproof Case LCD Display (with Backlight) Battery Compartment (on back) External Power/Data Connector (on back) Thumb Stick Page Button Power Button Step-by-Step Instructions to Get You Started (Turn this page and begin with Step 1) Operating the eTrex Legend Operating the eTrex Legend The Main Pages, Setting the Time Zone Backlighting/Contrast Adjustment Installing the Batteries1 The eTrex Legend operates on two AA batteries (not included), which are placed in the back of the unit. Rechargeable Alkaline, NiMH, NiCad or Lithium batteries may be used, but cannot be charged in the unit. Stored data will not be lost when changing the batteries. To install the batteries: 1. Remove the battery cover from the back of the unit by turning the D-ring 1/4 turn counter-clockwise and pulling out. 2. Insert the batteries observing proper polarity as shown at the right. 3. Reinstall the battery cover by turning the D- ring 1/4 turn clockwise. Battery CoverD-Ring Slot for Carry Lanyard Attachment 2 3 Start Up Sequence To turn the unit On: 1. Press and hold the POWER button. 2. Press the PAGE button to acknowledge the copyright. 3. Carefully read the warning message and press the PAGE button to acknowledge and proceed to the Satellite Page. The unit may take up to 5 minutes to establish a position the first time you use it outside with a clear view of the sky. After that, it should take only 15 to 45 seconds. When the Legend has acquired enough satellite signals to determine your location, a “Ready To Navigate” message and your location coordinates and elevation are shown. Satellite Page: displayingSatellite Position, Signal Strength, Location, and Elevation Using the Button Functions The PAGE button: • Press to cycle through main pages. The POWER button: • Press and hold to turn the unit On/Off. • Press to toggle the backlighting On/Off. External Power Protective Cover and Data Connector Connector Indexing (Alignment) Bar NOTE: While designed to be held and operated in the left hand, the unit can be used with the right hand, if preferred. rent location as a waypoint. LEGENDThe THUMB STICK: (When moved or pressed in, button ‘clicks’) • Press to enter highlighted options or confirm messages. • Move Up/Down or Right/Left to move through lists, highlight fields, on-screen buttons, icons, enter data or move the map panning arrow. • Press in and hold for two seconds to mark your cur- The FIND button: • Press to access the Find Menu. The ZOOM IN and OUT buttons: • When on the Map Page, press to Zoom in and out. • When on the Satellite Page, press to adjust the screen contrast. LCD Display 4 Previewing the Main Pages All of the information you need to operate the eTrex Legend is found on the five Main Pages (or display screens). To preview these pages, ...