AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. DIRECTV is an official trademark of DIRECTV Inc., a unit of GM Hughes Electronics. DISHTM Network is an official trademark of EchoStar Communications Corporation. ExpressVu is a property of Bell ExpressVu, a wholly owned subsidiary of Bell Satellite Services

The display is updated to show the new route leg. Restart Cross Track Error (XTE) Reset XTE is useful if you find yourself off track and want to go straight to your target, rather than get back onto the original track. Whilst following a route, or going to a target point, you can restart the XTE. This sets the XTE to zero and moves the origin to the vessel’s actual position. . To restart XTE: 1. Press the GOTO key. If following a route, the following functions are displayed: STOP FOLLOW RESTART

Apelco is a registered trademark of Raymarine Holdings Limited (Registered in all major marketing territories) . AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. DIRECTV is an official trademark of DIRECTV Inc., a unit of GM Hughes Electronics. DISHTM Network is an official trademark of EchoStar Communicat

In this case, proceed to 'Cutting the bracket'. • There are two alternative slots for the bracket in the back cover of the wheel drive (Slot 1 and Slot 2). • Locate the motor tube where: • a 55 mm (21/e in) hole can be cut in the bulkhead/pedestal (if required) • the seal and ring can be secured around the motor tube • there is sufficient space behind the mounting location to allow at least 10 mm (0.4 in) clearance around the motor (see diagram below) CAUTION: Mount the drive so the motor

Set to a level appropriate for your needs SmartPilot® ST7002 Controller r Use? or ▲ to adjust response level. Press disp to return to previous mode. To Adjust Lighting Level 1 sec Use disp to adjust lighting level. Wait 10 sec to return to previous mode. \j3uick Start GuideJ Display Layout disp Press to display data pages Press for 1 second for lamp control Press for 3 seconds for power off resp Press to display response level track When the Autopilot is activated, press to folow

Not all radar echoes are produced by valid targets. Spurious echoes may be caused by: • Side lobes. • Indirect echoes. • Multiple echoes. • Blind sectors. • Sea, rain, or snow clutter. • Interference. Through observation, practice, and experience, you can generally detect these conditions very quickly and use the radar controls to minimize them. Side Lobes Side lobe patterns are produced by small amounts of energy from the transmitted pulses that are radiated outside the narrow main beam. The ef

Its accuracy can be affected by many factors, including equipment failure or defects, environmental conditions and incorrect handling or use. It is the user’s responsibility to exercise common prudence and navigational judgement. This device should not be relied upon as a substitute for such prudence and judgement. CAUTION: Do not connect/disconnect the GPS Antenna from the display unit whilst power is applied. Such action could cause irreparable damage. WAAS Satellite Differential GPS WAAS prov

Format PAL 752 x 582 pixels NTSC 768 x 494 pixels Video connector Imager 1/ 3 Sony Super HAD CCD (Super Hi resolution) Horizontal resolution 550 TVL Scanning system PAL 625 lines NTSC 525 lines 2: 1 interlaced Red +12 V Video output Composite 75 Ohms Black - 0 V D8537_1 Infra red 14 IR LEDs If you do not have a breaker in the power circuit, an in- line 0.5 A quick blow fuse should be fitted to the positive (red) lead of the cable. LED spectrum 30 degrees for 15m Maintenance and Troubleshooting M

U UUUUUS SSSE EEER RRR’ ’’’S SSS G GGGU UUUI IIID DDDE EEE D DDDo oooc cccu uuum mmme eeen nnnt ttt N NNNo ooo..._ 8 8881 1112 2220 0007 777_1 111 F FFFe eeeb bbbr rrru uuua aaar rrry yyy 2 2220 0000 0002 222 R RRRa aaay yyyT TTTe eeec ccch hhh N NNNa aaav vvvi iiig ggga aaat ttto ooor rrr 4 444. ...0 000 R RRRa aaay yyym mmma aaar rrri iiin nnne eee, ,,, I IIIn nnnc ccc. ... F FFFt ttt.. . L LLLa aaau uuud ddde eeer rrrd ddda aaal llle eee E EEEn nnng gggi iiin nnne eeee eeer rrri iiin nnng ggg

Press again to accept the new course mode Press to select Wind Vane mode res m Press to resume previous course Press to adjust calibration, response and gain course change keys Port 1° Starboard 1° Port 10° Starboard 10° auto Press to activate the Autopilot standby + auto Press for Wind Vane mode standby Press for Manual Control L To activate the Autopilot For Manual Control 115176 To change the Autopilot Heading To follow a Route set on a Chartplotter