84-41 P/N 1023704 Rev. B (1) - 11/99
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each set will be visible one at a time allowing finer footplate height adjustment. 7. Insert the footplate tube into the front rigging support. 8. Push IN the release buttons and reposition the footplate assembly to the desired height. 9. Ensure that the release buttons fully protrude from holes on both sides of the front rigging support. 10. Rotate cam lock lever DOWN to LOCKED position. 11. Reinstall
1081003) provided with the Bath Lift, contact a healthcare professional, dealer or technical personnel before attempting to install this kit, otherwise, injury or damage may occur. This kit MUST be installed by an Invacare Dealer or technical personnel. INSTALLATION WARNINGS After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. Use proper lifting techniques to avoid injury. Keep back straight and be
1. Loosen, but DO NOT, remove the two (2) flat screws, washers and locknuts that secure contracture footplate to the footplate hinge. 2. Tilt the contracture footplate UP/DOWN to achieve desired angle. 3. Retighten the two (2) flat screws, washers and locknuts that secures the contracture foot plate to the footplate hinge. 4. If necessary repeat STEPS 1-3 on remaining contracture footplate. Contracture Assembly Footplate Hinge only. FIGURE 6 - ANGLE ADJUSTMENT OF THE CONTRACTURE FOOTPLATE Contra
1036900, 1036901, 1064227, 1086189, and 1086190 SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact Carrier/Dealer for further instruction. This kit includes the following: DESCRIPTION QUANTITY Anti-Tipper 2 Anti-Rattle* 2 *NOTE: Not included with Kit Nos. 1064227, 1086189, and 1086190. NOTE: To ensure the correct model anti.tipper is used, refer to Rear Anti.Tipper Application Chart on page 4. Safety Summary To ensure the safe and p
1123847 1 MPR Tray Assembly Kit 6. Secure the pivot arm and two (2) tray tabs to the tray with four (4) flange screws. Securely tighten flange screws. Repeat for support arm. 7. Insert pivot arm and support arm into recliner frame underneath armrests. Flange Screws FIGURE 1 - REPLACING THE TRAY - MODEL 6905A Invacare Corporation USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z4G4 Canada 800-668-5324 Invacare is a
Consulte la FIGURE 1. NOTA: Las etiquetas en ingles se incluyen en la FIGURE 1 para facilitar la determinacion del lugar adecuado. 2. Despegue una (1) etiqueta del adhesivo. 3. Coloque la etiqueta de advertencia o precaucion adecuada directamente sobre la etiqueta en ingles en el lugar determinado en el PASO 1. 4. Repita los PASOS 1-3 para colocar cada etiqueta. Para obtener mayor informacion sobre los repuestos, servicios y productos Invacare por favor visite la pagina Part No 1130213 3 Kit de
1048919, 1048920, 1048921, and 1048922 SAVE THESE INSTRUCTIONS NOTE: These instructions apply to the 9000 XT/XDT and the 9000 SL with adjustable back angle option. NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact Carrier/Invacare for further instructions. Safety Summary A WARNING DO NOT install this equipment without first reading and understanding this instruction sheet. If you are unable to understand the warnings, cautions and instructions, contact a hea
ROD KIT Kit No. III0IS4 Assembly, Installation and Operating Instructions Yes, you can: SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact Carrier/ Dealer for further instruction. SAFETY SUMMARY To ensure the safe installation and adjustment of the Telescoping I.V. Rod Kit, these instructions MUST be followed: GENERAL WARNINGS DO NOT install or use this equipment without first reading and understanding this instruction shee