(Gr. 5) 74 75 735-0249 736-0173 Chute Flapft Flat Wash. .28 I.D.ft 40 710-0380 Hex Bolt 5/16-18 x 1.75" Lg. 76 749-1004 N Chute Supportft 41 681-0004A N Flail Housing Ass’y.—L.H. 77 781-0633 Flat Striptt 42 681-0117 N Flail Housing Ass’y.—R.H. 78 781-0515 Front Support Bracket 43 735-0639 Spark Plug Boot (Optional) 79 781-0574 Back Up Plate 44 — Engine — 764-0199A Bag (Not Shown) 45 681-0104 N Bracket Ass’y.—R.R. — 723-0400 Safety Glasses (Not Shown) 46 681-0123 N Bracket Ass’y.—

5) 1.12 16 736-0119 L-Wash. 5/16" I.D. 59 726-0214 Push Cap 5/8" Dia. Rod 17 710-0825 Hex Bolt 1/4-20 x 3.75" Lg. 60 737-0195 Drain Elbowf 19 750-0793 Chute Hinge Spacer 1.66" Lg. 61 750-0786 Spacer .64 I.D. x .38" Lg. 20 711-0835 Clevis Pin .5" Dia. x 4.62" Lg. 62 738-0814 Shredder Axlef 22 712-0291 Hex Ctr. L-Nut 1/4-20 Thd. 738-0813 Shredder Axleft 24 781-0457 Shredder Screen 63 734-1600 Wheel Ass’y. Comp.t 25 714-0149B Internal Cotter Pin 3/8" Dia. 734-1597 Wheel As

BOX 368022 • CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO. 770-97-7B Model 462В, 463C, 465A 7B — Page 2 Model 462B, 463C, 465A PARTS LIST FOR MODELS 462B, 463C, 465A CHIPPER SHREDDERS REF. PART REF. PART NO. NO. CODE DESCRIPTION NO. NO. CODE DESCRIPTION 1 742-0571 Blade 48 710-0376 Hex Bolt 5/16-18 x 1.0" Lg. 2 710-1254 Hex Patch Bolt 3/8-24 x 2.25" (Gr. 5) (Gr. 8) 49 711-1128 N Lock Rod 4 736-0217 L-Wash. 3/8" I.D. H.D. 50 712-0429 Hex L-Nut 5/16-18 5 736-0427

See figure 12. It is possible to feed too fast. It will take some experimenting with feeding rates to get the most out of your shredder without stalling the engine. Rotate the material. A steady flow of material provides the best results. Under certain conditions, it may be necessary to push the materials into the inlet guide assembly. When this becomes necessary, use a small diameter stick --NOT YOUR HANDS. The stick should be of a size that will be ground up if it gets into the impeller asse

.531" I.D. x 937 4 711-0579 Flail Spacer 7/32" Lg. O.D. x .09 5 11455 Cutting Finger 33 11459 Flail 6 736-0921 L.-Wash. 1/2" Scr.* 34 711-0564 Flail Spacer 23/32" Lq. 7 726-0111 Palnut 3/16" Dia. 35 711-0578 Clevis Pin .50" Dia. x 3.0" Lq. 8 712-0922 Hex Jam Nut 1/2-20 Thd.* 36 736-0247 FI.-Wash. .406" I.D. x 1.25" 9 714-0507 Cotter Pin 3/32" Dia. x 3/4" O.D. Hdn. Lg.* 37 736-0217 L.-Wash. 3/8" Scr. H.D. 10 11465-488 Chute Deflector 38 710-0151 Hex B

An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the unit. The blade can be tested by balancing it on a round shaft screwdriver or nail. Remove metal from the heavy side until it balanced evenly. See figure 16. NOTE When reassembling, make certain the opening on the back-up plate is toward the bottom of the unit. The back-up plate may be reversed to provide a new cutting edge. 9 I When reassembling the blade, tighten to between 375 and

Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, the gasoline should be drained and disposed in a safe manner. Always allow the machine to cool before storing in any enclosure. 3 NOTE The right and left side of your shredder is determined from operator's position. FIGURE 1 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY 1. (1) 7/16" Open End or Box Wrench 2. (1)1 /2" Open End or Box Wrench 3. ( 1 ) Adjustable Wrench 1. Remove the shredder,

Keep proper balance and footing at all times. 10. The engine governor settings on your machine must not be altered, changed, or tampered with. The governor controls the maximum safe operating speeds and protects the engine and all moving parts from damage caused by overspeed. 11. Do not transport machine while engine is running. 12. Do not operate engine if air cleaner or cover directly over carburetor air intake is removed, except for adjustment. Removal of such parts could create a fire haz

BE CERTAIN AIR CLEANER IS CLEAN AND ATTACHED TO THE CARBURETOR BEFORE ADJUSTING CARBURETOR. DO NOT MAKE UNNECESSARY ADJUSTMENTS. FACTORY SETTINGS ARE SATISFAC^ TORY FOR MOST APPLICATIONS AND CONDITIONS. 8 MAINTENANCE Ac WARNING ( Disconnect spark plug wire and ground it against the engine before performing any repairs or maintenance. ENGINE Refer to the separate engine manual packed with your unit for all engine maintenance procedures. Read instructions carefully. AIR CLEANER The air cle

734-1600). *For faster service obtain standard nuts, bolts and washers locally. ttUsed with 10x4 Wheel (Steel—Part No. 734-1597). If these items cannot be obtained locally, order by part number and size as shown on parts list. 7C — Page 5 7С — Page 6 t Models 643C, 645C, G47C, 648C, 649C and 650C Models 643C, 645C, 647C, 648C, 649C and 650C PARTS LIST FOR SHREDDERS IEF. №. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 742-0571 Blade 43 735-0639 Spark Plug Boot (Option