Votos - 4, Puntuación media: 3.8 ( )

Fabricar: Air King Tamaño del archivo: 162.95 kb Nombre del archivo: Idioma del manual:

3. Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads of one end of the Threaded Pipe that will be screwed into the Motor Mounting Adapter. (Figure 1 - Inset) 4. Screw Threaded Pipe into Motor Mounting Adapter. The Threaded Pipe MUST BE screwed in at least 4 full revolutions. Do not allow Loctite #243 to dry before joining. Tighten provided 1/4” Set Screw into Motor Mounting Adapter. (Figure 1) 5. Open second tube of Loctite #243 by snapping tube neck just below end cap. Be Certain to follow all warnings noted on Loctite #243 tube. 6. Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads of the opposite end of the Threaded Pipe that is now screwed into the Motor Mounting Adapter. (Figure 1 - Inset) 7. Screw Threaded Pipe with Motor Mounting Adapter to the Pipe Mounting Flange.TheThreaded Pipe with Motor Mounting Adapter MUST BE screwed in at least 4 full revolutions into the Pipe Mounting Flange. Do not allow Loctite #243 to dry before joining. (Figure 1) 8. Tighten provided 1/4” Set Screw into Pipe Mounting Flange. (Figure 1) CAUTION: FAN IS HEAVY AND MAY REQUIRE TWO PEOPLE TO MOUNT. 9. Attach pull string to motor speed switch, if desired For Oscillating Motor: Place the flat section on the Motor Mounting Adapter next to the Motor Neck. (Figure 2A) For Non-Oscillating Motor: Slide the Motor Neck Slot over the Motor Mounting Adapter. Align the 1/2” diameter hole in the Adapter with the 1/2” diameter holes in the Motor neck Slot. (Figure 2B) 10. Insert the 1/2” X 1” Hex Bolt (3/4” head) through the Motor Neck, and the Motor Mounting Adapter. Place 1/2” diameter Split Lockwasher then the 1/2” diameter Hex Nut (3/4” head) and tighten fully with 2 adjustable wrenches. 11. From the same side of the Motor Neck, insert one 1/4-20 X 1 5/8” Carriage Bolt through the Arc-Shaped Slot in the Motor Neck and Hole in the Motor Mounting Adapter. To Fasten: Place one 1/4” Flatwasher, one 1/4” Internal Tooth Lockwasher, a second 1/4” Flatwasher and then tighten the Adjustable Knob over the remaining threads. GRILL AND BLADE ASSEMBLY (Figures 3 and 4) NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non- oscillating motor. One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to securely tighten the Bolt could result in damage to the Fan and/or personal injury. 3. Hold the Front Grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten Front Grill to Rear Grill by slidi...

Descargar ahora

Introduzca dos números de la imagen: