Carefully remove your heater from the box. please save the carton for off-season storage. 2. Make sure the unit is in the OFF position before plugging the heater into the outlet. 3. Place heater on firm level surface. 4. Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps. NOTE:The power light will remain lit while heater is plugged in. OPERATING INSTRUCTIONS Your heater is equipped with a technologically advanced

Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction. How to Obtain Warranty Service In the U.S.A. (Stamp comment Approved bellvei 28.05.2008 6:17:59 bla

Wall Mount Installation: This product weighs 25 lbs. Do not install alone. Mounting Template with instructions is attached below to make mounting your Fireplace Heater easy. • Wall Mount Hardware Kit includes: 4 - 1.5” Phillips head self tapping screws 4 - toggle bolts 2 - mounting brackets IMPORTANT: Before drilling into any wall ensure no electrical cables are present in the area. Max. height of 47” (1.2 m). Make sure you allow at least 3 feet (1m) of space on the sides of unit. 1. Remove stan

2. 3. 4. 5. 6. 7. 8. 9. 10. 11. e gasoline, paint, or flammable liquids are used or stored. 12.Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by the manufacturer may cause hazards. 13.DO NOT use outdoors. AUTO SAFETY SHUT-OFF WITH INSTANT TIP OVER PROTECTION This heater is equipped with a patented, technologically- adva

2. When the desired comfort level is reached, slowly lower the Thermostat just enough to stop the heater. 3. The heater automatically turns ON and OFF to maintain the selected comfort level. 4. The Temperature light turns on and off as the heater cycles to indicate that the heater is maintaining the selected comfort level. 5. The Power light illuminates when the heater is plugged into the outlet. NOTE: • It is normal for the heater to cycle ON and OFF as it maintains the selected comfort level.

KEEP THIS NUMBER FOR FUTURE REFERENCE. Bionaire® and Bionaire® Logo are registered trademarks of The Holmes Group, Inc. SmartTouch™ is a trademark of The Holmes Group, Inc. HEATER SERVICE INSTRUCTIONS 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void the warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 2. If you need to exchange the unit, please return it

11. DO NOT use outdoors. 12. To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked. 13. To disconnect heater, set controls to OFF, then remove plug from outlet. 14. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts. 15. Alway

Please check and take action if any of these potential problems are affecting your heaters ability to adequately warm your room. Supplemental Heat - Portable electric heaters are intended for supplemental heating of rooms to heat the room your in and turn down the central heat thermostat. They are not intended to replace central heating systems. do NOT attempt to repair or adjust any electrical or mechanical functions on this heater. doing so will void warranty. The inside of the heater contains

The "Set" temperature is displayed next to the "Room" temp. The unit will cycle on and off to maintain the "Set" temperature. The default room temp = 72.F/22.C. In this mode the unit will run to maintain the "Set" temperature. 2. Press Mode button on remote again. The remote screen displays "Auto" and "high". The "Set" temperature is displayed next to the "Room" temp. The "Auto" light on unit stays illuminated. The unit will cycle on and off to maintain the "Set" temperature at high wattage (150

Figure 3 low high auto mode HIGH (1500 Watts) AUTO LOW (1000 Watts) MODE Note: The "auto" light only illuminates when the unit is set to "auto" mode by the remote. B. Remote is ON and Unit is ON: 1. Press the Mode button on the unit. The unit will then switch "Modes"; either from "Low" to "High", "High" to "Off" or "Auto" to "Off" . The unit’s lights will reflect the change. The Remote will display a different mode – the mode in which it was left. If a button is pressed on the Remote, the Remote