The gas supply to the infra-red heater must be connected and tested in accordance with national, state, provincial and local codes along with the guidelines in this manual. Refer to the latest edition of the ANSI Z223.1 (NFPA 54) Standard. Important! Before connecting the gas supply to the infra-red heater(s): • Check for conditions such as drafts or other variables which might cause excessive movement of the unit and cause damage to the gas connection. Ensure that the unit is securely mounted a

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain these instructions for future reference. Dayton® Patio Heaters Description Dayton high-intensity patio heaters become highly efficient generators of infrared radiation by heating a ceramic refractory material to incandescence. The principal operation is to pass a gas-air mixture through a perforated ceramic refractory, and ignite it o

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. General Safety Information ▲warnings WARNING: Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning. DANGER: Carbon monoxide poisoning may lead to death! Carbon Monoxide Poisoning: Early signs of carbon mono

4. Remove and wash in clean fuel. Blow dry and replace. 5. a. Clean by blowing compressed air through nozzle from outlet end of nozzle. b. Replace nozzle if cleaning does not solve the problem. 6. Move heater to warmer environment until fuel flows freely. 7. Be sure air filters are clean. 8. Check fuel filter for air leaks and for tightness of fit where it is connected to fuel line. Ignition Troubles WARNING: DISCONNECT HEATER CORD! HIGH VOLTAGE! Heater will not ignite, but motor runs for a

Make sure that combustible materials are at least 8 feet from the hot air outlet, and 4 feet from sides and top. 3. Safely fill the fuel tank with kerosene or No. 1 fuel oil, as listed in the fuel guide below. 4. Check the reset button on the air intake end of the heater and make sure it is pushed in. 5. Plug the heater into any properly grounded 3-wire extension cord. NOTE: As soon as the heater is plugged in, it will start. Should your heater not start immediately, check the Troubleshoot

NO. DESCRIPTION PART NO. QTY. REF. NO. DESCRIPTION PART NO. QTY. 1 2 3 4 Upper shell Screw, #10-16 x 1/2" Combustion chamber assembly Photocell bracket 098511-64 M15823-27 098512-07 M16660 1 8 1 1 27 28 29 30 Bushing Bushing Screw, #10-16 x 1/2" Clip nut M30865-02 M50104-02 M11084-27 M11271 -8 1 1 5 6 7 8 Screw, #6-32 x 3/8" Photocell assembly Burner assembly Screw, #10-16 x 1/2" M10908-2 M16656-4 ■ t M11084-27 1 1 31 32 33 34 Screw, #8-18 x 1/4" Fuel tank Fuel cap (includes gasket) Flame out

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. Description Dayton portable oil-fired heaters are designed to provide temporary heat. They must be used with adequate ventilation, 120V, 60 Hz electrical power, and kerosene, or No. 1 fuel oil. THEORY OF OPERATION 1. There are four basic systems within the heater: the fuel system, air system, ignition system, and flame-out control system. 2. An air pump on o

NO. PART NO. DESCRIPTION QTY. REF. NO. PART NO. DESCRIPTION QTY. 23 M51073-01AZ Lower shell 1 33 M51002-01 Cap gasket 24 M30865-02 Bushing (photo cell 1 34 M51122-01 Circuit board support wires) 35 M51060-03 Safety control board, 1 _ 25 M30865-02 Bushing (transformer 1 PCB lead to spark plug) 36 M51157-01 Hex nut 12 mm 1 26 M30865-02 Bushing (transformer 1 (Secure PCB to lead to spark plug) , brackets) 27 M50104-02 Bushing (airline and 1 37 ■M11143-1 Strain relief bus

Co. (Dayton) to the original user against defects in workmanship or materials under normal use (rental use excluded), for 90 days after date of purchase. Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as Dayton designates, shipping costs prepaid, will be repaired or replaced at Dayton’s option. For warranty claim procedures, see "Prompt Disposition" below. This warranty gives purchasers specific legal rights, and purchaser

If you see globules of water in the bottom, drain and flush the tank and filter with clean fuel, b. Refill with fresh, clean fuel. FORM 5S1792 MODELS 2E510A, 2E511 A, 3E218A & 3E219 01582. Trouble Shooting Chart (Continued) SYMPTOMS POSSIBLE CAUSE(S) CORRECTIVE ACTION Heater burns, but puffs 2. Dirty air filters causing reduced 2. Remove and clean the air filters. of smoke can be seen; air flow through nozzle, resulting Be sure air intake is not blocked. heater will not burn in low