20802 Kensington Boulevard, Lakeville, MN 55044 USA • 1-888-427-3973 THIS PRODUCT MAY BE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413

Adjust or replace inlet regulatorif necessary. C. Valve. Replace valve and thermocouple interrupter. 7. 3 short beeps while the motor turns. A. Batteries are low. Replace batteries - quality alkaline recommended. WARNING: Creating anelectrical short between the batteries/battery box and metal parts of theappliance may render the receiver inoperable. 8. Pilot flame lights but there isno main gas flow. A. Manual override know (ifequipped) is in MANposition. Turn Manual override know to ON position

Note: ensure that you leave adequate room to remove and replace the front screen or optional front. Hearth & Home Technologies Inc. • SFE-35 • 4050-313 Rev C • 01/08 2 Fireplace Dimensions 33.75 in. 85.7 cm 1/2 in. (13 mm) L 48 in. 121.9 cm 34 in. 86.4 cm Rough Opening Height 12.75 in. 32.4 cm Rough Opening Depth 22 in. 55.9 cm 36.5 in. 92.7 cm Rough Opening Width 30.5 in. 77.5 cm 33.6 in. 85.4 cm 35 in. 88.9 cm Flush Nailing Flange Note: The bottom surface of this fireplace must be elevated to

WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN ELECTRICAL SHOCK OR FIRE MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. SERVICE MUST BE PERFORMED BY A QUALIFIED SERVICE AGENCY. USC TUV Listed as SFE-35 Homeowner’s Installation & Operating Manual Note: The device complies with Part 15 of the FCC Rules. Operation is subject

• The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire. • At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown. • At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown. • Add a 1/4 inch insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switc

Figure 3.1 Appliance Locations NOTE: For actual appliance dimensions refer to Section 16. A B C D E Inches 45-1/8 34-3/8 63-7/8 25-1/4 No maximum Millimeters 1146 873 1622 641 A . . A B C B E B D In addition to these framing dimensions, also reference the following sections: • Clearances and Mantel Projections (Section 3.C and 3.D) • Vent Clearances and Framing (Section 6). NOTE:These dimensions are for fl ush wall fi nishing method. For a recessed arch fi nishing method refer to Option B in Fin