PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. General Safety Information ▲warnings WARNING: Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning. DANGER: Carbon monoxide poisoning may lead to death! Carbon Monoxide Poisoning: Early signs of carbon mono

If you see globules of water in the bottom, drain and flush the tank and filter with clean fuel, b. Refill with fresh, clean fuel. FORM 5S1792 MODELS 2E510A, 2E511 A, 3E218A & 3E219 01582. Trouble Shooting Chart (Continued) SYMPTOMS POSSIBLE CAUSE(S) CORRECTIVE ACTION Heater burns, but puffs 2. Dirty air filters causing reduced 2. Remove and clean the air filters. of smoke can be seen; air flow through nozzle, resulting Be sure air intake is not blocked. heater will not burn in low

4. Remove and wash in clean fuel. Blow dry and replace. 5. a. Clean by blowing compressed air through nozzle from outlet end of nozzle. b. Replace nozzle if cleaning does not solve the problem. 6. Move heater to warmer environment until fuel flows freely. 7. Be sure air filters are clean. 8. Check fuel filter for air leaks and for tightness of fit where it is connected to fuel line. Ignition Troubles WARNING: DISCONNECT HEATER CORD! HIGH VOLTAGE! Heater will not ignite, but motor runs for a

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. ® Dayton Natural Gas Construction Heater Description Dayton Model 3VH19 heater is 100,000 Btu/Hr construction heater. This heater uses natural gas for combustion. It is primarily intended for the temporary heating of buildings under construction, alteration, or repair. This heater should never be use

NO. DESCRIPTION PART NO. QTY. REF. NO. DESCRIPTION PART NO. QTY. 1 2 3 4 Upper shell Screw, #10-16 x 1/2" Combustion chamber assembly Photocell bracket 098511-64 M15823-27 098512-07 M16660 1 8 1 1 27 28 29 30 Bushing Bushing Screw, #10-16 x 1/2" Clip nut M30865-02 M50104-02 M11084-27 M11271 -8 1 1 5 6 7 8 Screw, #6-32 x 3/8" Photocell assembly Burner assembly Screw, #10-16 x 1/2" M10908-2 M16656-4 ■ t M11084-27 1 1 31 32 33 34 Screw, #8-18 x 1/4" Fuel tank Fuel cap (includes gasket) Flame out

NO. PART NO. DESCRIPTION QTY. REF. NO. PART NO. DESCRIPTION QTY. 23 M51073-01AZ Lower shell 1 33 M51002-01 Cap gasket 24 M30865-02 Bushing (photo cell 1 34 M51122-01 Circuit board support wires) 35 M51060-03 Safety control board, 1 _ 25 M30865-02 Bushing (transformer 1 PCB lead to spark plug) 36 M51157-01 Hex nut 12 mm 1 26 M30865-02 Bushing (transformer 1 (Secure PCB to lead to spark plug) , brackets) 27 M50104-02 Bushing (airline and 1 37 ■M11143-1 Strain relief bus

Install the wheels (6) on the axle. IMPORTANT: The extended hub of the wheel should be positioned to- " ward the wheels support frame. Position the cap nuts (9) on the axle ends and gently tap with a hammer to secure. 2. Position the heater on the wheel support frame assembly with the combustion chamber end over the wheels. 3. Use four screws (7) and nuts (8) to attach the front handle to the top of the tank flange. The screws will go through the front handle, the tank flange and the wheel su

Make sure that combustible materials are at least 8 feet from the hot air outlet, and 4 feet from sides and top. 3. Safely fill the fuel tank with kerosene or No. 1 fuel oil, as listed in the fuel guide below. 4. Check the reset button on the air intake end of the heater and make sure it is pushed in. 5. Plug the heater into any properly grounded 3-wire extension cord. NOTE: As soon as the heater is plugged in, it will start. Should your heater not start immediately, check the Troubleshoot

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain these instructions for future reference. Dayton® Patio Heaters Description Dayton high-intensity patio heaters become highly efficient generators of infrared radiation by heating a ceramic refractory material to incandescence. The principal operation is to pass a gas-air mixture through a perforated ceramic refractory, and ignite it o

Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak that must be corrected. Correct all leaks at once. 6. Close propane supply valve. 4 Dayton Operating Instructions and Parts Manual Model 3VH20 Operation Review and understand the warnings in the General Safety Information section. They are needed to safely operate this heater. Follow all local codes when using this heater. TO START HEATER 1. Follow all installation, ventilation, and safety information. 2. Locate