Votos - 5, Puntuación media: 4.6
(
)
)
|
Resumen del manual
WARNING ON OFF a CRRFTSMRN ° ConsumerHelp Line 1-800-932-3188 WARNING / ADVERTENCIA Fig. 3 Thisversatilevariablespeedscrollsawisgreatfor makingtoys,puzzles,games,artwork,andjewelry.It isahandydo-it-yourself tool.Itcutswood,wood compositionplastic,andotherfibrous products, materialupto2 inchesthick.Italsocutsnonferrous metals(aluminum,brass,copper). KNOW YOUR SCROLL SAW Before attempting to use your saw, familiarize yourself with all operating features and safety requirements of your Sears Craftsman scroll saw. See Figure 5. ON/OFF KNOB WITH VARIABLE SPEED Your scroll saw has an easy access ON/OFF knob with variable speed. Pull the knob out to turn ON the saw, and push the knob in to turn OFF the saw. Turn the knob to adjust the speed from the high speed of approximately 1600 SPM (Strokes Per Minute) to the low speed of approximately 500 SPM. LOCK OFF POST Place a pad lock in the lock post next to the ON/OFF knob to lock the saw in the OFF position to prevent unauthorized use of the saw by children or others. TOOLLESS BLADE HOLDERS Retain and position the blade without the use of additional tools. Use the knobs for plain end blades or use the designed slots for pin type blades. TENSION QUICKRELEASE BLADE ,STORAGE DRAWER Fig. 4 BLADE STORAGE DRAWER Attached under the left side of the table is a blade storage drawer. It will hold up to 20 blades. Drawer snaps closed securely, See Figure 4. BLADE TENSION KNOBS Blade tension is controlled by a dual knob tension control system. The inner (smaller) knob, tension adjusting knob, is for making adjustments of the blade tension. The outer (larger) knob, quick release knob, is used to quickly set and release blade tension to facilitate blade changes. AIRDIAPHRAGM ADJUSTING KNOB KNOB HOLD DOWN FOOT LOCK KNOB PLAINENDBLADEKNOB HOLDDOWNFOOT/ BLADEGUARD SAWBLADE , SAWTABLE MOTOR LOCK OFF POS1 ON/OFF KNOB BLADE STORAGE DRAWER BEVEL ADJUSTMENT KNOB Fig. 5 10 HOLD DOWN FOOT/BLADE GUARD The hold down foot should be lowered until it just rests on top Of the workpieoe to prevent the workpieco from lifting while cutting, but not so much that the workpiece drags. The vertical portion provides e blade guard to prevent accidental blade contact. HOLD DOWN FOOT LOCK KNOB Allows you to raise or lower the hold down foot/blade guard and secure it at desired heights. SAWDUST BLOWER Keeps the line of cut on workpiece clean for more accurate scroll cuts. SAWDUST EXHAUST Your saw has a sawdust exhaust that fits a standard shop vacuum hose. See Figure 13. SAW TABLE Your scroll saw has an aluminum saw table that provides a working surface to support your workpiece. TABLE LOCK KNOB Allows you to tilt the table end lock it at the desired angle up to 45 degrees. BEVEL SCALE The bevel scale and indicator are located on the front of the saw for easy viewing. They show the angle of the table. ZERO DEGREE STOP FOR TABLE Located under the front of the saw table, the zero degree stop allows easy return and fine adjustment of the zero degree relationship between the table and the blade. Your Craftsman 16 in. scroll saw was fully assembled at the factory. Before operating this tool, it is important to check all alignments and settings. Normal handling during shipment may have changed settings. _1_ WARNING: To avoid serious personal injury from unexpected tool movement, always securely mount scroll saw to a workbench. MOUNTING SCROLL SAW TO WORKBENCH See Figure 6. If the scroll saw is to be used in a permanent application, we recommend that you secure it in e permanent location such as a workbench. When mounting the saw to a workbench, holes should be drilled through the supporting surface of the workbench using dimensions i_lustrated. • Each hole in the base of the saw should be bolted securely using 5/16 in. diameter machine bolts, lock washers, and hex nuts (not included). Bolt should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench. • Locate end mark the holes where scroll saw is to be mounted. • Drill (3) 3/8 in. diameter holes through workbench. • Place scroll saw on workbench aligning holes in the base with holes drilled in the workbench. • Insert all three 5/16 in. bolts and tighten securely with lock washers and hex nuts. Note: All bolts should be inserted from the top. Install the lock washers and hex nuts from the underside of the bench. Supporting surface where scroll saw is mounted should be examined carefully after mounting to insure that no movement during use can result. If any tipping or walking is noted, secure workbench or supporting surface before beginning cutting operations. 24 in. 9 3/8 in. dia, 6 5/8 in 12in. q4_1_ in. 19in. Fig. 6 11 CLAMPING SCROLL SAW TO WORKBENCH See Figure 7. If the scroll saw is to be used in a portable application, we recommend that you fasten it permanently to a mounting board that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size t...