23.NEVER use the miter saw in an area with flammable liquids or gases. 24.NEVER use solvents to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material. 25.SHUT OFF the power before servicing or adjusting the tool. 26.DISCONNECT the saw from the power source and clean the machine when finished using. 27.MAKE SURE the work area is clean before leaving the machine. 28.SHOULD any part of your miter saw be missing, damaged, or fail in any way, or any electrical compone

SE/ RS/C RRFTSM RN 10-INCH _BLE SAW oassembly . operating orepair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. Printed in U.S.A. Part No. SP5396 FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW if within one year from the date of purchase, this Craftsman Table Saw fail= due to a defect In material or workmanship, Sears will repair it, freeo! charge. This warranty applies only while this product is In use Inthe United States. WARRANTY SERVICEISAVAILABLEBYSIMPLYCONTACTINGTHENEAREST

install three Clips (furnished with Guard) 90° apart starting with one Clip at the end of the Guard as shown. LONG END of Clip facing AWAY from you. BELT GUARD _ N LONG END CLIPS 2. Reinstall Motor Pulley the same way it waswhen you aligned the Belt, 3. Place Belt on Saw Pulley. Insert end of Bell through opening in END of Guard. 4. Slip Belt over Motor Pulley. BELT 5. Press Guard onto Support sothat bottom of Guard is approximately 3/4 inch away from Belt. NOTE: To remove Guard, lift up on LONG

315.212340 315.242340 WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: Save this manual for future reference 983000-517 6-04 2 TABLE OF CONTENTS n Warranty 2 n Introduction 2 n General Safety Rules 3-4 n Specific Safety Rules 4-5 n Symbols 6-7 n Electrical 8 n Glossary of Terms 9 n Feature

Model and sedal numbers may be found on the left rear side of the base, You should record both model and serial number in a safe place for future use, FOR YOUR READ ALL INSTRUCTIONS CAREFULLY ® 10 iNCH DIRECT DRIVE TABLE SAW -assembly . operating o repair parts J Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U_S,A. Printed in US A Part No, SP5909 FULL ONE YEAR WARRANTY ON L,RAFTSNIAN STATIONARY TOOL If this stationary tool fails due to a defect in material or workmanship within one year fro

No exponga las herramtentas el_ctflcas a la Iluvla ni a amblentes h_medos. Cuando entra agua a una herramienta el_cLrica, se aumenta e! desgo de sufrirun choque el_ctrico,, 7, NO abuse del cord6n el_ctrico. NUNCA use el cord6n para transportar las herramtentas ni tire de! cord6n para desenchufadas. Mantenga el cord6n alejado del calor, det aceite, berries afltados o plezas m6viles. Reemplace inmediatamente los cordones qua est_n decades. Los cordones dafiados aumentan el riesgo de sufrirun chequ

Otherwise, it could get wedged against the blade and thrown violently. . Only the workpiece should be on the saws table. . Secure work. Use clamps or a vise to help hold the work when it is practical. USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES. . Use extra supports (tables, sawhorses, blocks, etc.) for workpieces large enough to tip. . Never use another person as a substitute for a table extension, or as an additional support for a workpiece that is longer or wider than the basic mite

The further apart the tips are, the greater the set. TABLE INSERT – Insert that is removed from the table to install / remove blades. It is also removed for dado cutting. When dado cutting, a dado insert plate must be used. THROUGH SAWING – Making a cut completely through the length or width of a workpiece. WORKPIECE – Material to be cut. Saw blade path Surface Leading edgeKerf Trailing edge Workpiece 17 1717 ASSEMBLY ASSEMBLE STAND (FIG. A, B, C) 1. Unpack all parts and group by type and size.

Failure to heed this warning can result in serious personal injury. CUTTING WITH YOUR COMPOUND MITER SAW ,& WARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury. CROSSCUTTING

315.214770 _1_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer HeUp Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 BeverUy Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: 983000-577 Save this manual for future reference 8-04 [] Warranty ................................................................................................................................................................