Use the arrow keys to select the desired unit of measure, then press the PWR key to clear the menu. Depth menu controls the unit of measure used to show depth. 39 TEMPERATURE UNITS OF MEASURE This unit can show the temperature (if a temperature sensor is attached) in degrees Fahrenheit or Celsius. To change the unit of measure, press MENU DOWN until the SYSTEM menu appears. Press UP ARROW, then press MENU until the TEMPERATURE menu appears. Use the arrow keys to select the measurement unit, then

The full sonar chart will scroll from right to left, showing you what's under the boat as you cruise across the water. 5. As you're watching the sonar returns, you can change the display by: Zoom in to enlarge the chart for more detail: press ZIN. Zoom out to return to full chart mode: press ZOUT. 6. If necessary, adjust sensitivity to improve chart readability. Press MENU|ENT and the Sensitivity Menu will appear on the left of your screen. Use ^ and v to change the setting. Boosting sensitivity

We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. For free owner's manuals and other information, visit our web site: Eagle Electronics P.O. Box 669 Catoosa, OK USA 74015 Printed in USA. Table of Contents Introduction..................................................................................1 Capabilities and Specifications....................................................1 Inst

Use ^ to select ON, which will turn on the alarm, then press PWR to clear the menu. If the voltage value falls below the alarm’s setting, the alarm will sound and a message will appear on the screen. Noise Rejection and ASP™ The ASP™ (Advanced Signal Processing) feature is a noise rejection system built into the sonar unit. It constantly evaluates the effects of boat speed, water conditions and electrical interference and automatically gives you the best display possible under most conditions. A

sonar! Your unit is a high-quality sonar designed for both professional and novice fishermen. All Eagle sonars have an automatic mode that finds and displays the bottom, fish, underwater structure and more – right out of the box. All you have to do is press the on (PWR) key. However, if you want to fine-tune your unit, press the MENU UP key. The FishEasy. 240 family has several powerful features you can control by scrolling through easy-to-use menus with the arrow and menu keys. To get started w

Eagle® is a registered trademark of Navico No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change withou

Ensure the radio is turned OFF anytime that the antenna is not connected. Installing the antenna: Rotate the antenna clockwise to fasten securely to the threaded connector on the top of the radio Note: Do not operate the radio or press PTT key without an antenna installed. 3. Installing the Belt Clip The belt clip supplied with your radio allows you to attach the radio to your belt. To install the belt clip: slide the belt clip to the back of your radio, make sure that the fitting Groove i

In this example, we will use 1.5 feet. This will be entered as a positive 1.5 feet, which makes the depth indicators perform as if the transducer is higher in the water than it really is. 75 1. Press MENU|MENU|v to SONAR SETUP|ENT. 2. Select SET KEEL OFFSET and press ENT. 3. The Keel Offset dialog box appears. Press v so the displayed number shows a plus (+) sign instead of the minus (–) sign. 3. To change the next digit, press > then use ^v to enter 1. Move to the next digit and enter 5, then p

No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle® and Cuda® 300 are registered trademarks of Navico. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do sowithout notice. All features and specifications subject to

Press v to select ON, then press PWR. Press MENU until the FISH ALARM menu appears. Press ^ to select ON, then press PWR. To turn off fish alarm press MENU until FISH ALARM appears. Press ^ to select OFF, then press PWR to clear the menu. Depth Alarms The depth alarms are triggered only by the bottom signal. No other echoes will activate these alarms. The depth alarms consist of a shallow and a deep alarm. The shallow alarm sounds an alarm tone when the bottom goes shallower than the alarm's set