7) -Attach guy lines to fabric guy loops at each corner and stake out (illus. 7) illus. 5 Shelter draped over partially assembled frame Use to adjust or tighten canopy Things You Should Know • Never store shelter, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your shelter. Use separate storage bag. • STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF. NEVER PULL ON THE SHELTER FABRIC OR SHELTER STAKE LOOP

-Do not assemble your shelter under trees. -For easier set up, two or more people are recommended. Center Hub Part (1) No. 9392-2251 Canopy Hub(5) Part No. 9392-2261 Leg Hub (5) Part No. 9392-2271 Canopy Poles (5) Part No. 9392-2321 Leg Poles (5) Part No. 9392-2301 Leg Connector Poles (10) Part No. 9392-2311 1 Pole & Hub Assembly Center Hub 2 3 4 -Begin with the Center Hub and Canopy Poles. -Insert the end marked TOP into the center hub and connect one pole at a time to the hub. (il

STITCH LINE BO SCREENHOUSE SETUP INSTRUCTIONS --MODEL 2000004415 Before you begin Read all instructions before set up. • Select a level site clear of rocks, branches, and other hard or sharp objects, to install your screenhouse. A WARNING: Keep clear of overhead power lines. • Do not set up your screenhouse under trees because of potential lightning strikes or falling tree limbs in inclement weather. • Secure with all stakes and guylines provided to prevent property damage or personal i

9392-1071 Hub (1) Part No. 9392-2101 Pole Sleeves 1 Pole Assembly Hub clipped to fabric -You will need to assemble and connect one pole at a time to the hub. -Do not completely assemble poles. a) Beginning at spring-clip end of pole, assemble all but the last shock-corded section. The pole and one section should curve downward. (illus. 1) b) Locate the center top clip on the fabric and attach it to the Hub (illus. 1), (illus. 3) c) Starting at the corner, Insert the spring-clip end of

(Fig. 1) • Unfold the arms of the screenhouse downward until they lay flat on the ground. (Fig. 2) • Extend the arms of the screenhouse away from the center hub. (Fig. 3) MODEL 2000004414 Raise the Screenhouse • Extend each of the telescoping leg poles until they snap into place. The screenhouse will raise as the leg poles are extended. (Fig. 4) 3 Stake the Screenhouse • Secure screenhouse by driving stakes through the webbing loops sewn to the screenhouse base. (Fig. 5 and Fig. 6) • Ke

-Do not assemble your shelter under trees. -For easier set up, two or more people are recommended. Center Hub Part (1) No. 9392-2251 Canopy Hub(5) Part No. 9392-2261 Leg Hub (5) Part No. 9392-2271 Canopy Poles (5) Part No. 9392-2321 Leg Poles (5) Part No. 9392-2301 Leg Connector Poles (10) Part No. 9392-2311 1 Pole & Hub Assembly Center Hub 2 3 4 -Begin with the Center Hub and Canopy Poles. -Insert the end marked TOP into the center hub and connect one pole at a time to the hub. (i

5) -Position each corner over a Leg Hub -Fully extend each pole by completing the interlocking of the shock corded pole sections. -Insert the brass hook into the hole near the base of the pole (illus. 6, 8) -From the inside of the shelter secure the pole frame to the shelter with the hook and loop closures. -Adjust poles to pull the shelter taut and stake down through the fabric loops at the end of each pole -Adjust hook straps to increase tautness (illus. 7) -Attach guy lines to fabric guy l

9392-2321 Leg Poles (5) Part No. 9392-2301 Leg Connector Poles (10) Part No. 9392-2311 1 Pole & Hub Assembly Center Hub 2 3 4 -Begin with the Center Hub and Canopy Poles. -Insert the end marked TOP into the center hub and connect one pole at a time to the hub. (illusl), (illus. 4) -Add a canopy hub to the five open ends of the center hub assembly. (illus. 2), (illus. 4) -Insert the clip end of Leg Connector Poles into the Canopy Hub. -Where the two open ends of the Leg Connector Pol

9392-1151 + Hub (1) Part No. 9392-1091 1 Pole Assembly Hub - You will need to assemble and connect one pole at a time to the hub. - Do not completely assemble poles. a) Beginning at spring-clip end of pole, assemble all but the last shock-corded section. The pole and one section should curve downward. (illus. 2) b) Insert the spring-clip end into one of the hub ports until it clicks into position. (illus. 1), (illus. 2) c) Repeat for each of the three remaining poles. (illus. 2) Illus.

The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the shelter fabric may render the flame-resistant properties ineffective. THE COLEMAN CO., INC. 3600 N. Hydraulic • Wichita, Kansas 67219 1-800-835-3278 • MADE IN SRI LANKA PRINTED IN SRI LANKA Rev. 11/04