To learn more about Porter-Cable visit our website at: PCA390 Copyright © 2002 Porter-Cable Corporation The Model and Serial No. plate is located on the frame. Record these numbers in the spaces below and retain for future reference. Model No. Type Serial No. Part No. D26052-023-0 BEFORE ASSEMBLY 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the high pressure hose from the gun. TO ASSEMBLE HOSE REEL 1. At

The swivel end must be used to attach high pressure hose to hose reel, see below to determine fixed and swivel ends. If quick connect socket is assembled on swivel end, remove and connect it to fixed end of hose. hose end without swivel hose end with swivel 6. Feed high pressure hose through slot (1) in flange assembly and connect to swivel (2). Tighten securely. 3. Apply sealant tape to hose reel inlet hose and assemble quick connect to hose reel inlet hose. 1 2 7. Make a loop in hose as shown.

Forest Service land and may also be legally required under other statutes and ordinances. Engine exhaust contains chemicals known, in certain quantities, to cause cancer, birth defects or other reproductive harm. D25803 2- ENG SAFETY GUIDELINES / DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please

Immediately after this occurs, the valve will close. Thermal Relief Valve Chemical Injection: Feeds cleaning agents into the pump to mix with the pressurized water and help in cleaning. Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute. HOW TO USE IMPORTANT: Read and understand how to use the pressure washer before operating. TO ADJUST PRESSURE The pressure setting is preset at the factory to achieve op

• If proper starting procedure is not followed, engine can kickback causing serious hand and arm injury. • The spray gun/wand is a powerful cleaning tool that could look like a toy to a child. • Reactive force of spray will cause gun/wand to move, and could cause the operator to slip or fall, or misdirect the spray. Improper control of gun/wand can result in injuries to self and others. • Spray directed at electrical outlets or switches, or objects connected to an electrical circuit, could resul

You should never run this pressure washer for more than 2 minutes without pulling the trigger to allow cool water to enter the pump and the heated (recirculated) water to exit. ASSEMBLY 1. Place handle assembly onto frame and connect handle to frame. 2. Connect wand to gun. Tighten securely. 3. Attach high pressure hose to gun. Tighten securely. 5. Assemble grommet kit and quick-connect nozzles as described in instructions supplied. 6. Add engine oil (supplied) to engine. Refer to engine manual

Save these instructions. See page 2 for Table of Contents. Parts Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Component Identification and Function . . . . . . . . . . . . 4 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Pump Serv

ENGINE Refer to engine manual for the manufacturer’s recommendations for any and all maintenance. PUMP NOTE: The pump was filled with oil at the factory. 1. Change pump oil after the first ten (10) hours of operation and every fifty (50) hours or yearly thereafter. 2. Change gear box pump oil after the first ten (10) hours of operation and every fifty (50) hours thereafter. How To Change Pump Oil 1. Loosen pump oil fill cap. 2. Place a container under the pump oil drain plug. 3. Remove pump oil

11- ENG D25806 TO SHUT DOWN IMPORTANT: Read and understand how to shut down the pressure washer before operating. 1. If you have siphoned chemicals, siphon a bucket of clean water through the chemical hose. NOTE: Failure to do so will cause damage to the pump. 2. Refer to engine manual for correct engine shut down procedure. NOTE: NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Sto

This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these sections. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,may res