Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
1. Connect the IDE cable to the adapter board. Figure D.1: Adapter Board and IDE Cable Figure D.2: Connecting the Adapter Board TPC-1261H User Manual 66 Note Pin 1 is marked red 2. Insert the adapter board into the CompactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.5: Inserted Adapter Board 67 Appendix D Connect the CD-ROM to the adapter board via the IDE cable and then connect the external power line to the CD-ROM. Figure D.6: Connect the CD-ROM via the IDE Cable Figure D.7: Plugging in the CD-ROM Drive TPC-1261H User Manual 68 E HDD Kit Assembly APPENDIX Appendix E HDD Kit Assembly TPC-1261H provides two way to assemble the HDD into the system. The ruggized HDD kit is to resist against the high vibration. E.1 Ruggedized HDD Kit Please follow the assembly procedure to install the HDD into the system. 1. Remove the default HDD cover from the system. The required parts are shown below. . Figure E.1: Removing the HDD cover TPC-1261H User Manual 70 Figure E.2: Required Parts 71 Appendix E 2. Place the base bracket on the rear case and carefully pull out the FPC cable through the hole of the bracket . Figure E.3: Opening the Top 3. Fasten the base on the rear case of the system by 5 screws. Figure E.4: Fastening the bracket TPC-1261H User Manual 72 4. Carefully connect the FPC cable to the HDD and then put the HDD insultor on the HDD. Figure E.5: Connectting the FPC with the HDD Figure E.6: Placing the HDD insulator on the HDD 73 Appendix E 5. Fasten the HDD holder with the HDD and HDD insulator. Please turn over the HDD holder and fasten them with 4 screws. Figure E.7: Reverse side of the HDD holder Figure E.8: Fastening the HDD holder TPC-1261H User Manual 74 6. Mount the HDD cushions with the HDD holder. Figure E.9: Mounting the cushions - 1 Figure E.10: Mounting the cushions - 2 75 Appendix E 7. Place the HDD holder on the rear cover of the system and then fasten the holder with the system by four screws. Then, the assembly of high vibration resistance HDD module is done. Figure E.11: Placing the HDD holder - 1 Figure E.12: Placing the HDD holder - 2 TPC-1261H User Manual 76 Figure E.13: Fastening the HDD holder E.2 Internal HDD Kit Assembly Please follow the steps to assemble the internal HDD kit. 1. Remove the default HDD cover from the system. Figure E.14: Removing the HDD cover 77 Appendix E 2. There are four rubber screw casings, and four screws. Places the screws into their casings Figure E.15: Placing a screw into its rubber casing 3. Mount the rubber HDD cushions on the HDD cover. Figure E.16: Mounting the rubber casings TPC-1261H User Manual 78 4. Connect the FPC cable to the HDD Figure E.17: Connecting the FPC cable 5. Put the HDD into the hole of the rear case. Figure E.18: Inserting the HDD 79 Appendix E 6. Lay the HDD insulator in right direction. Figure E.19: Laying in the HDD insulator 7. Place the default HDD cover on the system. Figure E.20: Placing the cover back into position TPC-1261H User Manual 80 8. Fasten the default HDD cover with the system. Figure E.21: Re-fastening the cover - 1 Figure E.22: Re-fastening the cover - 2 81 Appendix E 9. Place the bracket of PCI/104 on the slot and fasten it into place. Figure E.23: Fastening the PCI/104 bracket - 1 Figure E.24: Fastening the PCI/104 bracket - 2 TPC-1261H User Manual 82 APPENDIX F Touchscreen Installation & Configuration This appendix demonstrates how to install the PenMount touchscreen and set the configuration on TPC-1261H. This section uses Windows XP as an example. Appendix F Touchscreen Installation & Configuration F.1 Driver Installation Please insert the x86 TPC series support CD and go to the driver folder: (TPC-1261H\Driver\USB touchscreen). Click setup.exe Figure F.1: Setup.exe The screen displays the installation wizard for the PenMount USB software. Click “Next”. Follow the installation wizard step by step . Figure F.2: Install Wizard - 1 TPC-1261H User Manual 84 Figure F.3: Install Wizard - 2 Figure F.4: Install Wizard - 3 85 Appendix F F.2 Uninstall the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Programs. Figure F.5: Uninstall -1 Select PenMount USB. Click Remove button. Then, select “Yes” to remove the PenMountUSB driver and reboot the system .. Figure F.6: Uninstall -2 TPC-1261H User Manual 86 F.3 Touchscreen Calibration The “PM”, the icon of the PenMount Control Panel, is in the menu bar after the touchscreen installation. Please click the icon “PM” to call Pen- Mount Control Panel. It contains six functions: Calibrate, Draw, Option, and About. About shows the driver version. Calibrate Two ways to calibrate the touchscreen include “Standard Calibration” and “Advanced Calibration”. Standard Calibration is to adjust most touchscreens. Figure F.7: Standard Calibration -1 87 Appendix F Figure F.8: Standard Calibration -2 Figure F.9: Standard Calibration -3 TPC-1261H User Manual 88 Note Touch the red squares in sequence...
Otros modelos de este manual:Monitores - TPC-1261H (10.37 mb)
Monitores - TPC-1261H (10.37 mb)
Monitores - TPC-1261H (10.37 mb)
Monitores - TPC-1261H (10.37 mb)