Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
• When only one signal is connected, it is automatically detected. The default setting is D-SUB. EXIT Exit the OSD(On Screen Display). (Power Button) Turns the power on or off. Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode, the power indicator blinks blue. ENGENGLISH ENGENGLISH ENGENGLISH ASSEMBLING AND PREPARING 6 setting up the Monitor set Attaching the stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. CAUtIon Lay a foam mat or soft protective cloth on the surface to protect the screen from damage. 2 Attach the stand Base and then tighten the screw to the right with a Coin. DetachingthestandBase 1 Place the Monitor set with the screen side down on a flat and cushioned surface. 2 Turn the screw to the left, and then pull out the stand Base from the stand Body. standBase standBase CAUtIon yyThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. ASSEMBLING AND PREPARING 7 Mounting on a table 1 Lift and tilt the Monitor set into its upright position on a table. Leave a 10 cm (minimum) space from the wall for proper ventilation. 10 cm 10 cm 10 cm 10 cm 2 Connect the Power Cord to a wall outlet. 3 Press (Power) button on the front switch panel to turn the power on. ENGENGLISHWhenyouadjusttheangle,donotholdthebottomoftheMonitorsetframeasshownonthefollowingillustration,asmayinjureyourfingers. Donottouchorpressthescreenwhenadjustingtheangleofthemonitor. wARnInGTiltfrom+15to-5degreesupordowntoadjusttheangleoftheMonitorsettosuityourview. noteFrontRear15-5 UnplugthepowercordbeforemovingtheMonitortoanotherlocation.Otherwiseelectricshockmayoccur. CAUtIon ENGENGLISH ENGENGLISH ASSEMBLING AND PREPARING 8 UsingtheKensingtonsecuritysystem The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visitConnect the Kensington security system cable between the Monitor set and a table. TheKensingtonsecuritysystemisoptional. Youcanobtainitfrommostelectronicsstores. note Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 10 cm 10 cm 10 cm 10 cm When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop. Please use VESAstandard as below. yy784.8 mm (30.9 inch) and under * Wall Mount Pad Thickness : 2.6 mm * Screw : . 4.0 mm x Pitch 0.7 mm x Length 10 mm yy787.4 mm (31.0 inch) and above * Please use VESAstandard wall mount pad and screws. ASSEMBLING AND PREPARING 9 Model IPS225T/IPS235T VesA (A x B) 100 x 100 standard screw M4 number of screws 4 CAUtIon yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur. yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury. yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel. yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty. yyUse only screws and wall mounts that meet the VESAstandard.Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. note yyUse the screws that are listed on the VESA standard screw specifications. yyThe wall mount kit will include an installation manual and necessary parts. yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer. yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length. yyFor more information, refer to the instructions supplied with the wall mount. ENGENGLISH 10 USING THE MONITOR SET UsInG tHe MonItoR set ENGENGLISH Connecting to a PC yyYour Monitor set supports Plug & Play*. *Plug&Play: APCrecognizesaconnected device that users connect to a PC and turn on, without device configuration or user intervention. D-sUB connection Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations. DVI-D connection Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations. note yyWhen using a D-Sub signal input cable connector for Macintosh yyMac adapter ForApple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGAconnector on the supplied cable to a 15 pin 2 row connector. USING THE MO...
Otros modelos de este manual:Monitores - IPS235T (1.1 mb)