MAIN COMPONENTS of PHV Series constant pressure variable speed system • One multistage vertical pump, Goulds Pumps SSV series. • Hydrovar® pump mounted variable speed drive • Pressure transducer for constant pressure control, connected to the Hydrovar drive. • NEMA 4X fused disconnect panel with corrosion resistant durable plastic; external on/off switch with lockout/tagout. Panel is bracket mounted directly to pump. • Electrical panel for control and protection, with casing made of plastic mate

Item Part # Description Qty. Item Part # Description Qty. 41A 07721 O-Ring 3 51A 12564 Valve Seat 6 32 06118 Radial Shaft Seal 3 41B 13223 Support ring 3 51B 12565 Valve Plate 6 32A 13215 Grooved Ring 3 41C 12055 O-Ring 6 51C 12566 Valve Spring 6 33A 07721 O-Ring 3 41D 07693 Support Ring 6 52 05166 O-Ring 6 44 06096 Sleeve 6 57 05167 O-Ring 3 45 13360 Leakage Seal 3 GP6132 TORQUE SPECIFICATIONS Position Item# Description Torque Amount 10 13133 Inner Hexagon Screw 30 ft.-lbs. 36 13219 Plunger Con

Gas engine power outputs must be approximately twice the pump power requirements shown above. We recommend a 1.1 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements, use the following formula: GPM X PSI 6 GP7132 AND GP7136 REPAIR INSTRUCTIONS NOTE: Always take time to lubricate all metal and non-metal parts with a light film of oil before reassembling. This step will help ensure proper fit, at the same time pro

Gas engine power outputs must be approximately twice the pump power requirements shown above. We recommend a 1.1 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements, use the following formula: GPM X PSI 1400 3 GP7132 and GP7136 PARTS LIST ITEM PART DESCRIPTION OTY. I 07600 Crankcase 1 2 13000 Oil Filler Plug Assembly 1 4 07601 Crankcase Cover 1 5 07602 Seal for Cover 1 8 07603 Oil Dip Stick 1 9 01009 O-Rin

Item Part # Description Qty. 39 05235 O-Ring for Seal Retainer 3 51A 05246 Valve Seat 1 42 05238 O-Ring 3 51B 07653 O-Ring for Valve Seat 1 44 05240 V-Sleeve 9 51C 05247 Inlet Valve Seat 1 47A 05242 O-Ring 6 51D 07732-0100 Valve Spring 1 51F 05248 Valve Spring Guide 1 Oil Seal Kit # 09612 52A 07658 O-Ring 2 Item Part # Description Qty. 32 07624 Radial Shaft Seal 3 33A 07627 O-Ring 3 5 GP7170-4000 REPAIR INSTRUCTIONS NOTE: Always take time to lubricate all metal and non-metal parts with a light f

Carefully, remove seal rings (40) and sleeves (42) with a screw driver. 9 GP8055/GP8060/GP8065 PUMP REPAIR INSTRUCTIONS 7) Be careful not to damage the seal sleeve (39) and pressure ring (41). Check the inner diameter of the pressure ring for wear and if necessary replace together with seals (40) and (42). Clean all parts. New parts should be lightly coated with silicon grease before installation. Inert the seal unit (40, 41, 42 43) into the sleeve. Push the ceramic plunger carefully through the

Item Part # Description Qty. 33A 05056 O-Ring 3 38A 13286 O-Ring 6 33B 05057 Compact Ring 3 38B 05281 Support Ring 6 33C 05058 Radial Shaft Seal 3 39A 05066 O-Ring 6 40 07723 Seal Ring 3 Inlet Valve Kit - #09587 42 05277 V-Sleeve 9 Item Part # Description Qty. GP8060 - #09617 53B 05078 Inlet Valve Seat 1 Item Part # Description Qty. 53C 05079 Valve Plate 1 38A 06667 O-Ring 6 53D 07658 O-Ring 1 39A 05066 O-Ring 6 53E 05080 Valve Spring 1 40 05067 Seal Ring 3 53F 05081 Valve Spring Guide 1 42 0506

Up to 2000 PSI ......... (140 bar) Speed .............................................................. Up to 580 RPM ........ 580 RPM Inlet Pressure .................................................. Up to 29 PSI ............ (2.0 bar) Plunger Diameter ............................................ 2.55” ......................... 65mm Plunger Stroke ................................................ 2.83” ......................... 72mm Crankshaft Diameter.......................................2.76”

Gas engine power outputs must be approximately twice the pump power requirements shown above. We recommend a 1.15 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements, use the Following formula: Electric HP = (GPM X PSI) / 1460 Gas HP = (GPM X PSI) / 1100 GXR2424 GAS ENGINE HORSEPOWER REQUIREMENTS* M P R M P 2G 1000PSI 1S00PSI 2OOOPSI 24OO2PSI З4S0 22.4 2.2 З.З 4.4 2222S.2 * Engine power varies based o

Gas engine power outputs must be approximately twice the pump power requirements shown above. We recommend a 1.15 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements, use the Following formula: Electric HP = (GPM X PSI) / 1460 Gas HP = (GPM X PSI) / 1100 5 HR3030 ELECTRIC HORSEPOWER REQUIREMENTS RPM GPM 1500 PSI2000 PSI 2500 PSI 3000 PSI 3450 3.0 3.1 1 4.1 5.1 6.2 HR3030 Gi REQ AS HORSEPOWER UIREMEN