Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
The Light Copilot is an eight channel controller with two separate chase zones. Each zone is switchable from an audio or a timed chase sequence. Chase intervals vary from 0.1 seconds to 10 minutes. The controller has a built in microphone for easy audio chase sequences. Chases can be made to run to sound via an internal microphone or and external RCA audio line input. Audio chase sensitivity is adjustable by a rotary knob on the front panel. A “Latch” switch can override the chase function, to remain an individual channel on while the other maintain their chase sequence. You can daisy chain up to three power packs per a controller for easy installation and enhanced flexibility. The power pack uses high quality triacs for increased reliability. This unique controller allows for a single power source i.e. the controller unit receives it’s power from the relay pack via the 9 pin com cable. Operating Instructions Set-Up: 1. Connect the supplied 9 pin com cable from the out put of the controller unit to the input of the power pack. 2. Plug in the power pack to a standard AC outlet. Note: The controller unit does not come with an external power supply, an external power supply is only needed if you are running two or three power packs. 3. If desired, plug in the Bar-T-Cue/FS remote foot switch control using the 1/4” stereo jack connection on the rear of the controller unit (Bar-T-Cue/FS switch may be purchased as a separate option) Basic Operation: 1. After you have completed the set-up procedure, be sure main power is off and connect your desired lighting effects to the power relay pack. Note: There are two sockets per a channel on the relay pack you can plug an effect into either socket, or use both sockets to control two different lights to turn on at the same time. 2. Once you have connect your desired effects to the relay pack you can use the the “Latch buttons” to turn the fixtures on and off, or use the “Flash Buttons” to momentarily turn fixture on and off. 3. The controller unit controls to separate 4 channel zones: Each zone may be controlled independently of each other. The zones may chased through a build in timer or through an audio source (internal or external). 4. To run the fixtures to the chase sequence; Turn the on/off (Fig 10) switches to the on position for the fixture you want to include in the chase sequence. Use the speed knobs (Fig. 3) in conjunction with the chase time switches (Fig. 7) to adjust the chase speed to your ideal settings. See page 2 Chase/Audio Selector. 5. To run the fixtures to audio; Turn the on/off (Fig 10) switches to the on position for the fixture you want to chase to audio. Use the audio knob (Fig. 2) to adjust the audio sensitivity to your ideal settings. 6. During the chase sequence or audio mode you can use the Latch or Flash Buttons, to manually override either the chase sequence or the audio mode, and leave a fixture running. 7. You may use the Stand-By button to black out all controller functions and output American DJ Supply® Los Angeles Ca. Light Copilot Page 1 Controls and Functions: Controller - Front Panel CONTROL OUTPUT DC IN +9V~+12V 200MA MIN. AUDIO IN FOOT CONTROL PIN CH 5VCC 9876543 4 21 32 1 8 7 6 Controller - Rear Panel American DJ® POWER AUDIO SPEED SPEED STAND BY CH1-4 CH5-8 1 5 1110987 6432 1 12 13 14 1516 1718 19 20 OUTPUT INPUT CIRCUIT BREAKER AC POWER AC 120~60Hz,15A Relay Pack - Side View 1. Power Switch - Applies main power to the unit 2. Audio Control - This knob controls the audio sensitivity the unit will react to. 3. Chase Speed Control - Two sperate knobs to control independent chase speed for channels 1-4 and channels 5-8. 4. Latch Buttons - Pressing these buttons will maintain power to the fixture connected to the corresponding channel. 5. Channel Indicators - These LED’s will glow indicating channel activity. 6. Stand-By Indicator - This LED will glow indicating controller is in Stand-By mode. 7. Chase Audio Selector - These 3 pos...