Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
¦ Removing the lens cover Be sure to remove the lens cover when the power is turned on. If the cover is left on the projector, it could become deformed due to heat. Power cord connector (Supplied) ¦ Turning the power on 1 Press the ON/STANDBY button. The power is turned on, and the ON/ STANDBY indicator lights green. After a moment, the start-up screen appears. Remote Control Control panel Start-up screen CAUTION • Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyesight. • Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. • Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of the unit. Doing so could result in injury and/or damage the object. Notes • The start-up screen will disappear after a moment. You can also configure the system to prevent the start-up screen from appearing. To do this, use the Default setting menu p.34. • The first time you use the projector after purchase, after the start-up screen disappears, the start menu is displayed p.26. • Do not touch the lens directly with your hand. If fingerprints or stains are left on the projection lens surface, they may interfere with the projector’s ability to project images on the screen. Operations 25 ¦ Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. To shut off the power, press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a while without conducting any operations. The message will disappear shortly. (This operation is no longer valid after the message disappears.) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. ABFLASH A During cooling ,the ON/STANDBY indicator flashes. In this state, the power cannot be turned back on. However, there is no problem with unplugging the power cord in this state. B In standby mode Note • The projector consumes about 6W of power in standby. We recommend that you unplug the power cord if you will not be using the projector for an extended period. Precaution • If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light. • Right after turning off the power, the unit may become very hot, especially air exhaust and the bottom of the unit. Please handle with care to avoid burn injuries. After cooling complete When cooling lamp Basic operations 1 Turn on the power. Turn on the power by following the instructions in “Turning the power on” p.24. 2 Select the language (When using the first time). When the projector is used for the first time after purchase, the start menu for language (to display the menus and messages on screen) and configuration is displayed in English. (if the screen is out of focus, adjust it according to the step 6.) Use the , , or button to select the desired language and press the button. Message for setup confirmation is displayed in a selected language. Notes • When the projector is turned on the next time, the start menu does not appear upon startup. • The language can also be set via the Default setting menu p.34. • This owner’s manual assumes that English has been selected. 3 Activate the connected device. Turn on and start the connected device such as a computer. 4 Press the INPUT button. An image of the connected equipment is projected. Each time you press the INPUT button, it switches to another source signal from the equipment which is connected to the projector. Notes • When [Auto input search] is set to [On] in the Default setting menu p.34 (factory setting is [On]), the input is switched to the connected equipment that is outputting video signals each time you press the INPUT button p.43. • Right after the input source is switched to the other, the color of the image may change slightly. English French German Italian Spanish Portuguese Russian Swedish Turkish Romanian Simplified Chinese Traditional Chinese Polish Indonesian Norwegian Finnish Czech Hungarian Greek Danish Dutch 5 Projector placement angle adjustments The placement angle and the height of the projected image can be adjusted by the foot adjuster. j Lift up the front of the projector to the desired angle, then press the foot adjuster release button. The foot adjuster extends. Release the button to lock the position. k To adjust the horizontal angle, use the tilt adjuster. To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector. 6 Adjusting the screen size and focus j Use the zooming ring to adjust the screen size. k Use the focusing ring to adjust the focus. 7 Adjusting the volume with VOL+/- buttons The speaker volume can be adjusted when an audio signal i...
Otros modelos de este manual:Proyectores - Mobile Projectors TDP-XP2U (2.91 mb)
Proyectores - TDP-XP1U (2.91 mb)
Proyectores - TDP-XP2U (2.91 mb)