Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Please follow the instructions in this package. With proper care, your QuickStand screen will provide many years of reliable service. Two Section Frame (For presentation screens that are less than 120” in diagonal measurement) 1. Take the frame out of the case and remove its wrappings. Unfold the main joints as shown in (fig 1). 2. Once the main joints are unfolded, make sure that the snap latches “click” into the locked position. The frame should now be fully elongated as in (fig2). *Note: The snap latches will automatically lock when the joint is straightened. Press the snap latch button in order to release the lock. 3. While holding the bottom of the frame in place, lift the top of the frame to unfold the sides which will cause the snap latches lock when fully extended. Secure the corner braces into the locked position. The screen frame should now be fully opened as in (fig 3). fig 3Lock down the cornersSnap latchSnap latchTop fig 1 Rev043010-JA info@elitescreens.com Three Section Frame (For large presentation screens that are 120” or more in diagonal measurement) 1. Take the frame out of the case and remove its wrappings. Unfold the main joints making sure that both the end and middle spans are in prefect alignment as shown in (fig 4). 2. Make sure that the snap latches have locked the joints in the frame so that it is at its full horizontal extension as shown in (fig 5) 3. While holding the bottom of the frame in place, lift the top of the frame to unfold the sides which will cause the snap latches lock when fully extended. Secure the corner braces into the locked position. The screen frame should now be fully opened as in (fig 6). fig 4 fig 6Lock down the cornersSnap latchSnap latchTop Rev043010-JA info@elitescreens.com Standard T-Leg Support -Leg Support 1. Take the T-Leg out of the case and remove its wrappings. Fold down the support legs as shown in (fig 7). 2. Secure the corner braces into the locked position as shown in (fig 8) 3. Unfold the T-Leg’s main support until the snap latches “click” into the locked position as in (fig 9). fig 8Lock down the corners fig 7 fig 9Snap latch Rev043010-JA info@elitescreens.com AT-Leg (optional support buttress recommended for the large -Leg (optional support buttress recommended for the large screens with diagonal measurements of 150” and over) 1. Take the AT-Leg buttress out of the case and remove its wrappings. Unfold the buttress as shown in (fig 10). 2. Snap latches will automatically lock in the center joint. Use the snap latch buttons to unlock the end joints as shown in (fig 11). 3. Attach the AT-leg to the T-Leg by securing the locking bolts through the frame using the frame spacers between the metal parts as shown in (fig 12) (*Note: It is important to always use the plastic frame spacers between the pieces whenever connecting any of the aluminum surfaces such as T-bars to AT, SAT and Frame components.) fig 11Snap latch Rev043010-JA info@elitescreens.com SAT-Leg (optional added stability buttress recommended for the -Leg (optional added stability buttress recommended for the large screens with diagonal measurements of 180” and over) 1. Take the SAT-Leg out of the case and remove it wrappings as shown in (fig13). 2. Undo the snap locks to loosen and bend the joints for proper fitting as shown in (fig 14). 3. Attach the SAT-Legs by securing the locking bolts through the frame using the frame spacers between the metal parts as shown in (fig 15) fig 14 Rev043010-JA info@elitescreens.com Attaching the Frame to its Supports 1. Always use at least two locking bolts through the T-Leg Support, the Spacer and into the Frame on each side. 2. Height can be adjusted in 8” increments up or down. Normal screen height is 44” from the bottom of the frame to the floor. 3. Reverse this process to dismantle and pack away the screen. snap latch button Folding the Screen material for proper packing Please observe the following precautions before folding up the screen material. 1. Do not bring the viewing surface into contact with chemical solvents, sharp or abrasive objects, painted, varnished or plastic finished items.(*See the cleaning instructions for exceptions to this) 2. Make certain that the screen is laid out on a dry, clean and flat surface. Folding up the screen: Lay out the screen with the viewing surface facing up and cover it with flat (not crumpled) tissue or packing paper that is clean and unprinted. *Note: Do not ever use abrasive paper, newspaper or any printed material on your projection screen. 1. With the viewing surface facing up, fold the fabric in half from top to bottom. When folding, make certain that the viewing surface does not come into contact with the black binding, grommets or snap buttons. *Note: The screens are shipped from production with tissue paper in the folds that should be retained for future use. Rev043010-JA info...