Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
............... FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. N This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits. RGB 201 Rxi Universal Interface • Quick Start Guide Quick Start Guide — RGB 201 Rxi Step 1 Turn the equipment off and disconnect the equipment from the power source. Step 2 For positive or negative output sync (rather than sync following the input), RsGsBs video, or to clamp sync timing to back porch), open the interface’s case and configure the jumpers and/or DIP switches. See Internal Configuration, beginning on page 2-3, for details. Step 3 Rack, under-desk, or through-desk mount the interface as desired. Rack mounting — Use the optional 1U Rack Shelf, part #60-190-01, for rack mounting. Under desk mounting — Use the optional Under-Desk Mount Kit, part #70-077-01, to mount the DA under furniture. Thru-desk mounting — Use the optional Thru-Desk Mount Kit, part #70-077-02, to mount the DA through furniture. Step 4 Video input — Connect the RGBHV, RGBS, RGsB or RsGsBs video input to the 15-pin HD Input connector. Step 5 Audio input — Connect an unbalanced stereo audio source (such as a computer or a CD player) to the 3.5 mm mini stereo Audio connector for unbalanced audio input. See the figure below to wire the audio plug. Tip (Left)Sleeve (Gnd) Tip (Left) Ring (Right) Sleeve (Gnd) Step 6 Buffered monitor output — If desired, connect a local monitor or other device to this 15-pin HD female connector. Step 7 Video output — Connect an RGBHV, RGBS, RGsB or (if configured in step 2, above) RsGsBs video display or other device as shown on the next page. Quick Start Guide — RGB 201 Rxi, cont’d RGB 201 Rxi Universal Interface • Quick Start Guide RGBHVRHGVBSRGBSRGSBVHSRGsBRsGsBsRGBVH Step 8 Audio output — Connect an audio device, such as powered speakers, to this 3.5 mm, 5-pole captive screw connector for balanced or unbalanced audio output. The figure below shows how to wire the captive screw audio connector. Balanced AudioTipRingTipRingLRSleevesDo not tin the wires! Unbalanced AudioTipSleeveSleeveTipLR C Connect the sleeve(s) to ground (). Connecting the sleeve(s) to a negative (-) terminal will damage audio output circuits. Step 9 DIP switches — Configure the rear panel DIP switches as shown: Switch Position Switch Position 1 Up DDSP, no sync processing 5 Up Mono on left channel Down ADSP Down Stereo audio 2 Up RGsB or RsGsBs output 6 Up LCD backlight off Down RGBHV or RGBS output Down LCD backlight on 3 Up Serration pulses 7 Up ID bits 4 & 11 grounded Down No Serration pulses Down ID bits unterminated 4 Up Narrow V sync pulse 8 Spare Down Wide V sync pulse Step 10 Remote connector — Connect an RS-232 device to this connector for remote control. See chapter 3, Remote Control for details about SIS commands and the control software that is included with the interface. PinRS-232Function1— 2TXTransmit data (-) 3RXReceive data (+) 4— 5GndSignal ground6— 7—— 8—— 9—— — — — Female5196Male1569 RGB 201 Rxi Universal Interface • Table of Contents Table of Contents Chapter 1 • Introduction ...........................................................1-1 About this Manual .................................................................1-2 About the RGB 201 Rxi .........................................................1-2 Features .......................................................................................1-3 Chapter 2 • Installation and Operation .........................2-1 Installation Overview ..........................................................2-2 Internal Configuration ........................................................2-3 Sync polarity jumpers .............................................................2-4 Internal sync DIP switches (RsGsBs) .......................................2-5 Video clamping jumper .........................................................2-5 Mounting the Interface .....................................................2-6 Tabletop placement ...............................................................2-6 U...