Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Use only cable designed for DVI signals. • Limit or avoid the use of adapters, patch panels, or • couplers with the input DVI cables, the output DVI cables, and/or the twisted pair cables. Additional links in the chain reduce signal integrity and overall cable length performance. Always turn on the display before the DVI video source in • order for the source to retrieve the DDC from the display. No video signal or incorrect resolution or refresh rate — If the source device is not able to obtain EDID information when it is being powered on, it may not be able to send a video signal or the signal may have the wrong resolution or refresh rate. Ensure that the DDC DIP switches are set correctly for the • EDID source (see pages 3-2 to 3-5). The source device must be powered on after the display • device providing the EDID source has been powered on. Incorrect color or tint — Ensure that the twisted pair cables are terminated correctly and to the same standard on both ends of the cable (see page 2-14 and 2-15). Display device displays a flashing black or blue screen, snow, or other distortion — A device that is not High-Bandwidth Digital Content Protection (HDCP) compliant may be receiving HDCP-encrypted signals. The DVI DL 201 Tx/Rx is compatible with HDCP signals only when the EDID Minder is disabled. HDCP signals can be passed through to only one display (remote or local) and only that display shows the signal correctly. Signal on local monitor but not on remote display — Check that both output devices (local and remote) can handle resolutions equal to or greater than the EDID source. A Appendix A Reference Information Specifications Included Parts Optional Accessories Reference Information DVI DL 201 Tx/Rx • Reference Information A-2 Specifications Video Maximum data rate....................... 10 Gbps (3.3 Gbps per color) Maximum pixel clock.................... 330 MHz (165 MHz per link) Resolution range............................ Up to 2560x1600 @ 60 Hz Formats............................................ RGB and YCbCr digital video Standards......................................... DVI 1.0, HDMI 1.2 Video input and loop-through — transmitter Number/signal type...................... 1 dual link DVI-D input 1 dual link DVI-D local loop.through N Dual link DVI is backwards compatible with all single link DVI/HDMI signals. Connectors...................................... 2 DVI-I female (1 for input, 1 for loop.through) Interconnection between transmitter and receiver Connectors...................................... (3) RJ-45 per unit for 2 CAT 5/5e/7 or STP (shielded twisted pair) cables connecting the transmitter and receiver. Termination standards.................. TIA/EIA T568A or T568B. Pin configurations for each standard are available in the "Installation" chapter. Signal transmission distance 2560x1600 @ 60 Hz CAT 5/5e/6/7 STP cable Up to 125' (38 m) CAT 5/5e/6 UTP (unshielded twisted pair) cable Up to 100' (30 m) Longer distances are possible with lower rates N The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphics card, and display used in the system. DVI DL 201 Tx/Rx • Reference Information A-3 Video output — receiver Number/signal type...................... 1 dual link DVI-D N Dual link DVI is backwards compatible with all single link DVI/HDMI signals. Connectors...................................... 1 DVI-I female Control/remote — external device (pass-through) Serial control port input Transmitter.......................... RS-232 via (1) 3.5 mm, 3 pole captive screw connector Receiver............................... 1 set of proprietary signals on a female RJ-45 jack Serial control port output Transmitter.......................... 1 set of proprietary signals on a female RJ-45 jack Receiver............................... RS-232 via (1) 3.5 mm, 3 pole captive screw connector N Protocol is mirrored between the transmitter and the receiver. Serial control pin configuratins.... Captive screw connectors: 1-TX, 2=RX, 3=GND General Recommended cable type............. CAT 5/5e/6/7 (shielded or unsheilded) External power supply.................. 100 VAC to 240 VAC, 50/60 Hz, 6 W max., external; to 12 VDC, 2 A, regulated Power input requirements............ 12 VDC, 0.4 A for both transmitter and receiver N Each transmitter and receiver can be powered locally by an external power supply. The receiver can be powered remotely by a power supply connected to the transmitter on the other end of the CAT 5/5e/6/7 UTP or STP cable. Temperature/humidity................. Storage: -40 to +158 °F (-40 to +70 °C)/ 10% to 90% noncondensing Operating: +32 to +122 °F (0 to +50 °C)/ 10% to 90% noncondensing Cooling............................................ Convection, no vents Mounting Rack mount......................... Yes, with optional 1U, 9.5" deep rack shelf (RSU 129, #60.190.01 or RSB 129, 60.604.01); 1U, 6" deep rack shelf (RSU 126, #60.190.10 or RSB 126, 60.6...
Otros modelos de este manual:El receptor y el amplificador - Dual Link DVI Transmitter and Receiver DVI DL 201 Tx (1.27 mb)