Votos - 3, Puntuación media: 5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
A hard wall is highly reflective and does not significantly effect the frequency response of the reflected sound. “WALL” lets you control the level of the high frequencies to alter the sonic character of your listening environment by simulating a softer (S) or harder (H) wall. You can adjust from S to H in 17 steps. MID (0) setting designates a neutral wall made of wood. x REVB. XXX (Reverberation) Initial setting: MID (0) Before sound reaches our ears, it is reflected (reverberated) many times between he left and right walls, ceiling, and floor. In a large room, sound takes more time to bounce from one surface to another than in a smaller room. “REVERB” lets you control the spacing of the early reflections to simulate a sonically longer (L) or shorter (S) room. You can adjust from S to L in 17 steps. MID (0) designates a standard room with no adjustment. x SCR. (Screen depth) Lets you create the sensation that the sound of the front speakers comes from inside the screen in your listering room, like theaters. • OFF This function is not activated. • MID Normally, select “MID”. • DEEP Lets you create the sensation that the sound comes from a very large screen with a greate amount of screen depth. Advanced LEVEL menu parameters When “MENU” is set to “MENU EXP.”, all of the following parameters are displayed and adjustable. See page 38 for the LEVEL menu adjustments. Initial settings are underlined. All LEVEL menu parameters L R (FRONT) CTR XXX.X dB SUR.L. XXX.X dB SUR.R. XXX.X dB S.W. XXX.X dB MULTI CH IN S.W. XXX dB L.F.E. XXX.X dB* D.RANGE COMP.* * Adjustable only when “MENU” is set to “MENU EXP.”. continued Advanced Adjustments and Settings 45GB Advanced settings (continued) x L.F.E. XXX.X dB (LFE (Low Frequency Effect) mix level) Initial setting: 0 dB Lets you attenuate the level of the LFE (Low Frequency Effect) channel output from the sub woofer without effecting the level of the bass frequencies sent to the sub woofer from the front, center or surround channels via the Dolby Digital or DTS bass redirection circuitry. You can adjust from –20 dB to 0 dB (line level) in 0.5 dB steps. “0 dB” outputs the full LFE signal at the mix level determined by the recording engineer. When set to “OFF”, the sound of the LFE channel from the sub woofer is muted. In this case, the low frequency sounds of the front, center, or surround speakers are output from the sub woofer according to the settings made for each speaker (pages 21–22). x COMP. ( D.RANGE ) (Dynamic range compressor) Lets you compress the dynamic range of the sound track. This may be useful when you want to watch movies at low volumes late at night. • OFF The dynamic range is not compressed. • 0.1–0.9 The dynamic range is compressed in small steps to achieve the sound you desire. • STD The dynamic range is compressed as intended by the recording engineer. • MAX The dynamic range is compressed dramatically. Tip Dynamic range compressor lets you to compress the dynamic range of the soundtrack based on the dynamic range information included in the Dolby Digital signal. “STD” is standard compression, but because many sources have only light compression, you may not notice much difference when using 0.1– 0.9. Therefore, we recommend using the “MAX” setting. This greatly compresses the dynamic range and lets you view movies late at night at low volumes. Unlike analog limiters, the levels are predetermined and provide a very natural compression. Note Dynamic range compression is possible with Dolby Digital sources only. Advanced EQ menu parameters (front speakers only) When “MENU” is set to “MENU EXP.”, all of the following parameters are displayed and adjustable. See page 39 for the EQ menu adjustments. All EQ menu parameters BASS XXX.X dB BASS XXX Hz* TREB. XXX.X dB TREB. XXX Hz* * Adjustable only when “MENU” is set to “MENU EXP.”. x BASS XXX.X Hz (Front speaker bass frequency) Initial setting: 250 Hz You can adjust from 99 Hz to 1.0 kHz in 21 steps. x TREB. XXX.X Hz (Front speaker treble frequency) Initial setting: 2.5 kHz You can adjust from 1.0 kHz to 10 kHz in 23 steps. 46 GB Other Operations Other Operations Naming preset stations and functions You can enter a name of up to 8 characters for preset stations and functions and display it in the receiver’s display. 1 To index a preset station Rotate FUNCTION to select TUNER, then tune in the preset station you want to create an index name for (page 27). To index a function Rotate FUNCTION to select a function you want to create an index name for. 2 Press CUSTOMIZE. 3 Press the cursor button ( ) to select “NAME IN”. 4 Press ENTER. The cursor flashes and you can select a character. 5 Create an index name by using the jog dial and cursor buttons ( or ). Turn the jog dial to select a character, then press the cursor button ( ) to move the cursor to the next position. Tips • You can select the character type as follows by turning the jog dial. Alphabet (upper case) t Numbers t Symbols • To enter a blank space, turn...