Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
FIG. 1 DAS-TAMP4/8-SIG Tango amplifier Note that each Output on the Tango Amplifier represents two audio channels. •The DAS-TAMP4-SIG is a 4-channel amplifier that provides two Outputs. •The DAS-TAMP8-SIG is an 8-channel amplifier that provides four Outputs. Tango Amplifiers connect to the Tango Controller via one of the Zone Output connectors on the Controller, and provide either two or four additional Outputs for that single audio Zone. Features • High-quality sound - delivers 60 watts of high-quality sound per channel. • Expandable - stack up to three Tango amplifiers units per zone to allow up to 24 channels in a single zone (using the DAS-TAMP8-SIG). • Easy installation - SWT (Speaker Wire Technology) makes installation simple using four-conductor speaker wire. • Integrates with Tango Series, Delta Series and Mi Series controllers, as well as the W, C, C-DT and EL Series speakers. Product Specifications Tango Amplifiers Product Specifications Models Available: DAS-TAMP4-SIG 4-Channel amplifier: • US version (120V) - FG1103-21 • Int’l version (240V) - FG1103-23 DAS-TAMP8-SIG 8-Channel amplifier: • US version (120V) - FG1103-22 • Int’l version (240V) - FG1103-24 Dimensions (HWD): • 3 1/16” x 17” x 13 1/2” (7.68cm x 43.18cm x 33.52cm) •RU: 2 Weight: • DAS-TAMP4-SIG: 25.75 lbs (11.68 kg) • DAS-TAMP8-SIG: 32.30 lbs (14.65 kg) Power: • High current Torroidal power supply • Maximum: 634 W Average usage: • DAS-TAMP4-SIG: 250 W • DAS-TAMP8-SIG: 500 W Stereo Output: • Dual mono amplifier stage design • 60 W per channel (1 KHz continuous .006% @ 8 Ohms THD+N) • DAS-TAMP4-SIG: capable of providing 240 watts @ 8 Ohms • DAS-TAMP8-SIG: capable of providing 480 watts @ 8 Ohms Configuration: • Modular Design - configurable in single pairs up to either 4 stereo pairs (4 channels) 8 stereo pairs (8 channels). • Stackable (up to 3 Tango amplifiers) Control Options: • Metreau Audio Keypads (DAS-MET-6SRC, DAS-MET-NUM) • C-Series speakers using SWT • IR using a Stealth IR Receiver (DAS-IRRX-SWT) Front Panel Components: Light Bar • Blue light bar indicates power status. Status LED • Blue LED lights when active Tango Amplifiers Product Specifications (Cont.) Rear Panel Components: Power Switch & Receptacle The master power switch normally remains in the ON position. OUTPUT connectors (1-2 or 1-4): 4-pin connectors provide direct connection to speakers. • The DAS-TAMP4-SIG has 2 OUTPUT connectors • The DAS-TAMP8-SIG has 4 OUTPUT connectors From Controller: SWT input port (connects to a Delta, Mi or Tango Audio Controller) To Keypad: SWT output port (connects to Matrix keypad or interface) This connector can also be used to connect to a another Tango amplifier, to allow for expansion (up to three Tango amplifiers units per zone). Included Accessories: Power Cord Other AMX Equipment: DAS-MRMK Mi Series Rack Mount Kit (FG1101-60) Wiring and Connections Front and Rear Panel Components FIG. 2 provides views of the front and rear panels of the Tango amplifiers. Note that the front panel is identical for both Tango amps, and the only difference on the rear panel is the number of OUTPUT connectors (2 on the DAS-TAMP4-SIG, or 4 on the DAS-TAMP8-SIG). Light Bar (power status) Status LED To Keypad From Controller Outputs (2 or 4) Power Switch & Receptacle FIG. 2 Tango amplifiers (DAS-TAMP4-SIG shown) Note that each Output on the Tango Amplifier represents two audio channels. Cabling Instructions This installation uses low voltage cabling. Prior to installation, be sure to check for any wiring restrictions required by the electrical code in your area. The Tango amplifier is cabled using standard four-conductor speaker cable originating at the Tango Controller, passing through the Keypad, and terminating at the speaker location. AMX recommends using a bundled four-conductor 16-gauge stranded copper wire in a single continuous run. Connecting Outputs (Speakers) OUTPUT Connectors FIG. 3 provides the pinout configuration for the OUTPUT connectors on the Tango amplifiers. OUTPUT 1 L+ = Left audio channel (+) L- = Left audio channel (-) R- = Right audio channel (-) R+ = Right audio channel (+) L+ L-R-R+ FIG. 3 OUTPUT Connectors - Pinout Configuration Connecting SWT Speakers SWT Speakers are different from other speakers available on the market. They allow you to control a single zone of audio without a keypad being installed. Therefore, some different wiring practices must be considered for proper operation and control. This is achieved by “daisy-chaining” from the first speaker to the second speaker. The main run of 16/4 from the controller will go directly to the first speaker in the zone. SWT cabling follows the pinout configuration shown in FIG. 4: L = Left audio channel (+) D = Data/Power (+) G = Ground (-), also provides return for L/R audio LDGR R = Right audio channel (+) FIG. 4 SWT Connectors - Pinout Configuration • At the controller end, the wiring is left-to-right: L D G R. • At the speaker end, refer to the labeling on speaker PCB t...