Try to avoid over- adjustments. Conveyor Belt Replacement 1. To replace a worn conveyor belt, raise drum to highest position. Unplug machine from power source and unplug motor cord from control box receptacle. 2. Adjust conveyor take-up screw nuts (Figure 22) to relieve belt tension. Figure 21 (repeated) Figure 22 16 3. Remove the four bolts attaching conveyor assembly to base. Lift up and slide conveyor out to the side of the machine. 4. Set conveyor on motor side and slide conveyor belt off th

Hold the cleaning stick against the rotating drum and move it along the drum surface. It is good idea to use a shop brush or air nozzle to remove any cleaning stick crumbs from the drums before resuming sanding operations. Cloth-backed abrasives can be cleaned by soaking in paint thinner, or mineral spirits for 20 minutes to one hour. Then use a nylon brush to remove any buildup. Stretching Abrasive Life Abrasive life can also be increased by removing the abrasive strip from the drum and reversi

Read and understand this entire manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This sander is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a sander, do not use until proper training

In addition to the wide range of sanding grits, our variable feed rate and exclusive SandSmart™ technology provide unrivaled control over the sanding process. The JET 22-44 Pro-3 Drum Sander has the capacity to handle surprisingly large jobs despite its 52”-tall by 41”- long dimensions. The JET 22-44 Pro-3 Drum Sander can sand material up to 4”-thick and 44”-wide (2 passes). The design of the drum and conveyor also mean that it can handle material as short as 2 .”- long and down to 1/32”-thick!

POWBtMAHC Belt Disc Sander Loaded with features, the new 31A from Powermatic can tackle the most demanding tasks. Full cast iron construction allows both metal and woodworking to be done on the same machine and the Integral Dual Dust Port keeps both belt and disc portions clean, extending abrasive life. ■ The articulating table mounted on the 6" x 48" belt sander head can be used vertically, horizontally, or angled to accommodate any job. The belt head has an indexing pin with stops at 0, 45 a

6012 120 Volts 12,000 Orbits/Min. Uses 3-2/3” x 9” Sandpaper CATALOG NO. 6014 120 Volts 12,000 Orbits/Min. Uses 4-1/2” x 11" Sandpaper OPTIONAL DUST PICK-UP KIT CATALOG NO. 48-09-0300 For Use with No. 6014 Orbital Sander IMPORTANT-Before placing tool in operation, record the following information from nameplate. Model Number_ Serial Number_ Date of Purchase_ MILWAUKEE ELECTRIC TOOL CORPORATION 13135 West Lisbon Road • Brookfield, Wisconsin 53005 THIS SYMBOL ... ' IfJJ/'itainsJar ... IS

No utilice una herramienta danada. Coloquele una etiqueta que diga “NO DEBE USARSE” hasta que sea reparada (vea “Reparaciones”). Bajo condiciones normales, no se requiere lubricacion hasta que haya que cambiar los carbones. Despues de 6 meses a un ano, dependiendo del uso dado, envie su herramienta al Centro de Servicio MILWAUKEE mas cercano para que le hagan: • Lubricacion • Inspeccion y cambio de carbones • Inspeccion mecanica y limpieza (engranes, flechas, baleros, carcarza, etc.) • Inspeccio

Fig. B Fig. C EXTENSIONES ELECTRICAS Las herramientas que deben conectarse a tierra cuentan con clavijas de tres patas y requieren que las extensiones que se utilicen con ellas sean tambien de tres cables. Las herramientas con doble aislamiento y clavijas de dos patas pueden utilizarse indistintamente con extensiones de dos a tres cables. El calibre de la extension depende de la distancia que exista entre la toma de la corriente y el sitio donde se utilice la herramienta. El uso de extensiones i