10 OPERATION TO THROW SNOW (See Fig. 15) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Release the auger control lever to stop throwing snow. AUGER CONTROL LEVER FIG. 15 USING THE CLEAN-OUT TOOL (See Fig. 16) In certain snow conditions, the discharge chute may become clogged with ice and snow. Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or

cord on electric motors, thoroughly inspect the snow (d) Never fill containers inside a vehicle or on a truck or thrower for any damage, and repair the damage beforetrailer bed with a plastic liner. Always place contain-restarting and operating the snow thrower. ers on the ground, away from your vehicle, before 4. If the unit should start to vibrate abnormally, stop the fi lling. engine (motor) and check immediately for the cause. (e) When practical, remove gas-powered equipment Vibration is gen

Look for this symbol to point out important safety precautions. It means CAUTION!!! BE COME ALERT!!! YOUR SAFE TY IS IN VOLVED. WARNING: Always disconnect spark plug wire and place it where it can not con tact plug in order to prevent ac ci den tal start ing when setting up, transporting, ad just ing or making re pairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping surfaces. Do not use snow throwe

• Presionar hacia abajo la palanca del mando de la velocidad y mover la palanca hasta la posicion deseada ANTES de conectar la palanca del mando de guia de traccion Asegurarse de que la palanca vuelva en su lugar y se fije en la posicion deseada. PRECAUCION: No mover la palanca del mando de la velocidad cuando la palanca del mando de la guia de traccion esta conectada. Esto puede perjudicar al motor y/o a la maquina quitanieves. • Velocidades mas lentas son para nieve mas pesada y velocidades ma

After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine on your snow thrower has been shipped, from the factory, already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wa

Failure to observe the following safety instructions could result in serious injury or death. Look for this symbol to point out important safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. C

inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty. 23 24 REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 5224SEB (96193001000), PRODUCT NO. 961 93 00-10 32 31 32 30 31 12 10 11 13 15 15 12 16 17 16 23 22 27 41 27 22 17 11 15 15 14 7 6 2 5 5 3 1 4 4 4 4 3 8 28 28 9 18 19 26 24 24 25 5 5 REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 5224SEB (96193001000), PRODUCT

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and using your snow thrower. • Follow the instructions under “Maintenance” and “Storage” sec tions of this own er’s manual. 3 SAFETY RULES........................................................2-3 MAINTENANCE.....................................................14-15 PRODUCT S

Plastic cannot breathe, which allows con den sa tion to form and will cause your snow thrower to rust. IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm. an engine while in storage. 18 TROUBLESHOOTING See appropriate section in manual unless directed to a qualifi ed service center. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so equipped) in OFF position. 2. Safety ignition key is not inserted. 3. Out of fuel. 4. Throttle in STOP position. 5. Chok

Raise upper handle to the operating position and tight en handle knobs securely. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. SPEED CONTROL ROD HANDLE KNOB LOWER HANDLE PLASTIC TIE UPPER HANDLE FIG. 1 INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and