WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough Power Equipment McDonough.GA« 30253 A FUOUA MDUBTMEB Company Manual 06012 (l-4257)Rev. 1, 11/10/00 Printed in U.S.A. INDEX - MAIN CONPONENTS SUBJECT PAGE(S) Arm, Idler................... ............3.1-3.2 Assembly, Gear Box.......... ............1.2-1.3 Assembly, Spindle........... ...............3.3 Augers...

Detach cable from receptacle and engine. On jump start equipped models, refer to instructins provided in kit. NOTE: If engine does not start after five seconds of continuous cranking, release electric start button to prevent overheating of the starting motor. Locate and correct cause of starting problem before repeating electric starting attempt. WARM-UP PERIOD: Allow brief warm-up outside with clutches released to avoid stalling cold engine. Reset Choke as instructed in Engine Manual as the u

This two-stage Thrower will do a great job of clearing snow from your drives and walks on the rear engine Rider which not only provides weight on the rear drive wheels for excellent traction but gives you good forward visibility. This manual covers the recommended procedures for operating the unit as a snow thrower plus detailed instructions for converting the Rider to and from the mower mode as the seasons change. Before operating in the snow thrower mode, be sure to read the important safety i

NOTE: Allow the engine to warm up at SLOW throttle for a few minutes before operating the snowthrower at full speed. The engine will not develop full power until it reaches operating temperature. After warming up, always operate at full throttle. 11 Operation OPERATING THE SNOWTHROWER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger engage control (C, Figure 2) on the right-hand grip to begin auger r

24 INCH (60 cm) WIDTH 8 H.P. 24 INCH {60 cm) WIDTH 8 H.P, 28 INCH <70 cm) WIDTH 10 H.P, 28 INCH (70 cm) WIDTH aru Product Identification: When ordering parts, keep your products serial number and manufacturer's number in mind. Variations may occur in a part between early and later model products, causing the product serial number to be listed in the parts description whenever these variations occur. Record your I.D. numbers here for quick, future reference. Product Mfg. No__S/N_Mower Mfg. N

Kit Parts Ref. Description Qty. A. Searing 8. Nut. 3/8 C. Lockwasher. 3/8 D. Lift Arm E. Nut, Centerlock F. Trunnion, Rear G. Lift Rod H. Washer, 1 I. Lift Shaft J. Capscrew, 3/8-16 X 1 K. Capscrew, 5/16 L. Lockwasher, 5/1 6 M, Nut, 5/16 N. CaiviCraw-.7/1 8-1 4x 1-1/2 0. Upstop Plate P. Lockwasher, 7/16 Cl. Nut, 7/16 R. Capscrew, 7/16-14x 1-1/4 S. Lockwasher, 7/16 T. Nut. 7/16 U. Capscrew, 1/2-13 x 1-1/4 V. Lockwasher. 1/2 W. Nut, 1/2 X. Hitch Y. Trunnion, Front Z. Washer A

With the Thrower on a flat, level surface, the oil should be even with the lower edge of the check hole. Use an oil can containing the same weight and grade of oil specified for the engine crankcase to bring the level up to the point of overflowing from the hole. Reinstall the oil plug after servicing. CHUTE CRANK SERVICE If the chute does not crank easily after lubricating as specified under GENERAL LUBE SERVICES, loosen both nuts on the outside of the crank worm bracket as shown in figure 4

5. To lower the height of the scraper bar, raise the skid shoes. 6. If the scraper bar becomes worn, it can be replaced by removing the hardware attaching it to the snowthrower. A B Figure 3. Chute Deflector Adjustment (Some Models) A. Chute Deflector Knob B. Chute Deflector Figure 5. Skid Shoe Adjustment A. Scraper Bar B. Skid Shoe C. Nuts Figure 4. Remote Deflector Control (Some Models) A. Maximum Throwing Position B. Spring C. Control Handle C A A B C B 13 Operation FULL TRACTION Easy Turn™ L