Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5 meters. Illustration of MD20Q42 Approx. 5 meters Caution: Never throw batteries into a fire. Notes: • Be sure to use AAA size batteries. • Dispose of batteries in a designated disposal area. • Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations. • If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones. • When necessary to replace batteries in the remote control, always replace both batteries with new ones. • Never mix battery types or use new and used batteries in combination. • Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment. 12 5X30401A [E] (P08-12) 12 12/3/05, 3:29 PM ConnectionsConnections Antenna connections If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see page 14 for Cable TV connections. Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire) 75 ohm coaxial cable (not supplied) 300-75 ohm matching transformer (supplied) Antenna jack Antenna jack Connect the 75 ohm cable from the combination VHF/UHF antenna to the antenna jack. If your combination VHF/UHF antenna has a 300 ohm twin-lead wire, the use of the 300-75 ohm matching transformer may be necessary. Connections Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires) 300-75 ohm matching transformer (supplied) UHF 300 ohm twin-lead wire (not supplied) VHF 300 ohm twin-lead wire (not supplied) Antenna jack Combiner (not supplied) Connect the UHF 300 ohm twin-lead wire to the combiner (not supplied). Connect the VHF 300 ohm twin-lead wire to the 300-75 ohm matching transformer. Attach the transformer to the combiner, then attach the combiner to the antenna jack. Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires) UHF 300 ohm twin-lead wire (not supplied) VHF 75 ohm (not supplied) Antenna jack Combiner (not supplied) Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the combiner (not supplied). Attach the combiner to the antenna jack. 13 5X30401A [E] (P13-23) 13 12/3/05, 3:29 PM Connections Connections Cable TV connections This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company. For basic cable service not requiring a converter/descrambler box, connect the Cable TV 75 ohm coaxial cable directly to the Antenna jack on the back of the TV/DVD. 75 ohm coaxial cable If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A” position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/ descrambler box to tune scrambled channels. Incoming 75 ohm Cable TV 75 ohm cable to TV/DVD Antenna jack Antenna jack Converter/ descrambler If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to select channels. For subscribers to basic cable TV service For subscribers to scrambled cable TV service For subscribers to unscrambled basic cable TV service with scrambled premium channels Splitter B A Incoming 75 ohm Cable TV A/B switch 75 ohm cable to TV/DVD Converter/ descrambler Antenna jack 14 5X30401A [E] (P13-23) 14 12/3/05, 3:29 PM INPUT GAME Connecting to optional equipment You can enjoy VCR, camcorder or TV game with connection to external input. To select the external input, press INPUT and select “LINE” mode. INPUT GAME Connecting to optional equipment You can enjoy VCR, camcorder or TV game with connection to external input. To select the external input, press INPUT and select “LINE” mode. Connections To connect the TV/DVD to a VCR Pr...
Otros modelos de este manual:TV - MD20Q42 (2.99 mb)
TV - MD13Q42 (2.99 mb)
TV - MD20Q42 (2.99 mb)