Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
This will create a Heat Stage 1 demand. A small triangle to the left of this HEAT icon will flash or come on continually. Flashing means the equipment is going to turn on but is presently being held off by a system timer. (See Operational Information for timer descriptions.) Defeat timer by pressing INCREASE TEMPERATURE button (up and FAN buttons together). This will make the triangle stay on and turn on Heat Stage 1. To turn off, reduce heating set point below room temperature. The heating and the triangle will turn off within a few seconds. If the system has multiple heat stages, it will start on Heat Stage 1 and proceed to Heat Stage 2, 15 minutes later due to a staging timer which requires 15 minutes between successive stages. The INCREASE TEMPERATURE button (up and FAN buttons) cannot be used to defeat this timer. If set point is raised more than 5° above room temperature, the staging timer is defeated and the thermostat will call for higher stages within 5 sec. Use this method if there are only 2 stages of heat. If more than 2 stages of heat are available, do not use this method because once the demand exceeds 5°, the thermostat may jump to the highest stage. With more than 2 stages available, let the timer advance one stage every 15 minutes. TO TEST EMERGENCY HEAT (heat pump systems only): To test, press MODE button until EHEAT icon turns on. This will allow operation of auxiliary heat only. Raising set point above room temperature will turn on the first stage of auxiliary heating (W/W1). Raising set point more than 5° above room temperature will advance to full heat, if it is available (O/W2 or Y1/W2 will come on—see Table 2). Reducing set point below room temperature will turn all heat off. ® Step 6—Final Settings 1. Assuming the system is to be left in operation after the installation is complete, use MODE button to select between HEAT, COOL, EHEAT, or AUTO to provide the desired operation of heating, cooling, or both. 2. The default set points and programmed schedule conform to the Energy Star requirements of the U.S. Department of Energy for both heating and cooling. These provide energy saving temperature settings. 3. Turn on HOLD if fixed set points are to be used. If the programmed schedule is to be used, make sure the HOLD icon is off. 4. For further information on temperature selection and programming, refer to Homeowner’s Manual. 5. If AUTO mode is to be used, be sure both heat and cool set points are properly adjusted. 6. The FAN button may be used to select between AUTO (fan on only with equipment) and FAN (fan on continuously) fan modes. ® Step 7—Checklist 1. Put away tools and instruments, and clean up debris. 2. Review Homeowner’s Guide with owner. 3. Leave literature packet with owner. 4. Fill out and return survey card. 5 6 ® Table 2—Programmable Thermostat Quick Reference THERMOSTAT OUTPUTTSTAT Model Outdoor Unit AC/HPConfiguration(Switch C) StagingConfiguration(Switch D) 24vHot Common Fan HeatStage 1 HeatStage 2 Heat Stage 3 Heat Stage 4 Cool Stage 1 CoolStage 2 Reversing Valve AC01-B AC EITHER EITHER R C G W/W1 N/A N/A N/A Y/Y2 N/A N/A HP01-B HP OFF EITHER R C G Y/Y2 W/W1 N/A N/A Y/Y2 N/A O/W2 HP01-B AC ON EITHER R C G W/W1 O/W2 N/A N/A Y/Y2 N/A N/A 2S01-B 2-Speed AC ON EITHER R C G W/W1 O/W2 N/A N/A Y1/W2 Y/Y2 N/A 2S01-B 2-Speed HP OFF OFF R C G Y1/W2 Y/Y2 W/W1 N/A Y1/W2 Y/Y2 O/W2 2S01-B *1-Speed HP OFF ON R C G Y/Y2 W/W1 Y1/W2† W/W1, Y1/W2 Y/Y2 N/A O/W2 Y1/W2 is on without W/W1†AC = Air conditioner, HP = Heat pump, 2S = 2-speed, N/A = Not applicable, * = Intelligent Heat optionModel Numbers: TSTAT--PAC01-B, TSTAT-PHP01-B, TSTAT--P2S01-B MODEL AC SINGLE-STAGE SINGLE-SPEED THERMOSTAT FURNACE AIR CONDITIONER 24 VAC HOT FAN HEAT STAGE 1 COOL STAGE 1 N/A N/A R G W/W1 Y/Y2 O/W2 Y1/W2 R G W Y 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y C See note 1 SUGGESTED DIP SWITCH SETTINGS ON A B C D OFF OFF OFF OFF A98485 ® Fig. 2—Single-Speed Air Conditioner with Single-Stage Furnace—Model AC Thermostat TWO-STAGE OR MODEL AC SINGLE-SPEED VARIABLE-SPEED THERMOSTAT AIR CONDITIONER FURNACE 24 VAC HOT FAN HEAT STAGE 1 COOL STAGE 1 N/A N/A R G W/W1 Y/Y2 O/W2 Y1/W2 R G 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y C See notes 1 and 6 W/W1 Y/Y2 HUM W2 SUGGESTED DIP SWITCH SETTINGS ON A B C D OFF OFF OFF OFF A98486 ® Fig. 3—Single-Speed Air Conditioner with 2-Stage or Variable-Speed Furnace —Model AC Thermostat TWO-STAGE OR MODEL HP VARIABLE-SPEED SINGLE-SPEED THERMOSTAT FURNACE AIR CONDITIONER 24 VAC HOT FAN HEAT STAGE 1 COOL STAGE 1 HEAT STAGE 2 N/A R G W/W1 Y/Y2 O/W2 Y1/W2 R G 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y C See note 2 W/W1 Y/Y2 HUM W2 SUGGESTED DIP SWITCH SETTINGS ON A B C D OFF OFF ON OFF A98487 ® Fig. 4—Single-Speed Air Conditioner with 2-Stage or Variable-Speed Furnace —Model HP Thermostat 7 MODEL HP TYPICAL SINGLE-SPEED THERMOSTAT FAN COIL AIR CONDITIONER MODEL AC TYPICAL SINGLE-SPEED THERMOSTAT FAN COIL AIR CONDITIONER 24 VAC HOT FAN COOL STAGE 1...