Votos - , Puntuación media:
(
)
)
Fabricar: Healthrider
Tamaño del archivo: 1.51 mb
Nombre del archivo: 9f6bbb74-8334-43e5-8238-f0b7d82c9ea7.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
While another person lifts the rear of the Frame (1), attach the Rear Stabilizer (not shown) to the Frame with two M10 x 105mm Carriage Bolts (not shown) and two M10 Nylon Locknuts (not shown). 8 109 1 63 89 5 6 3 14 1 Grease 48 48 76 76 99 99 Tubes 2.Identify the Pivot Axle (14), which is the longest axle. Slide a Ramp Cover (48) onto an M6 x 16mm Patch Screw (76) as shown. Tighten the Patch Screw into one end of the Pivot Axle. Apply a small amount of the included grease to the Pivot Axle. Have a second person hold the two Ramp Spacers (99) against the sides of the Frame (1) so they cover the indicated tubes on the Frame. Align the round tubes on the Ramp (3) with the Ramp Spacers; make sure that the Ramp is turned as shown in drawing 3 below. Insert the Pivot Axle (14) into the Ramp, the Ramp Spacers, and the Frame. If necessary, tap the Pivot Axle with a rubber mallet to insert it. Slide the other Ramp Cover (48) onto an M6 x 16mm Patch Screw (76) as shown. Tighten the Patch Screw into the open end of the Pivot Axle (14). Tubes 3.Slide an M6 Washer (64) onto an M6 x 16mm Patch 3 Screw (76). Tighten the Patch Screw into one end of the Incline Axle (13). Apply a small amount of grease to the Incline Axle. Raise the Ramp (3). Insert the Incline Axle (13) into the welded tube under one side of the Ramp, through the motor screw, and then into the welded tube under the other side of the Ramp. As you insert the Incline Axle through the motor screw, make sure that the motor screw does not turn. Slide an M6 Washer (64) onto an M6 x 16mm Patch Screw (76). Tighten the Patch Screw into the open end of the Incline Axle (13). 13 Grease Motor Screw 76 64 3 64 76 4.Have another person hold the Upright (2) in the position shown. Make sure that the Upright is turned as shown in drawing 7 on page 8. Connect the Upper Wire Harness (95) to the Lower Wire Harness (42). Carefully pull the upper end of the Upper Wire Harness to remove the slack from the Wire Harnesses. Slide the Upright (2) onto the Frame (1). Be careful to avoid disconnecting or pinching the Wire Harnesses. Attach the Upright with three M10 x 25mm Button Screws (114) and three M10 Split Washers (57). 2 95 42 114 114 114 57 57 1 4 2 7 111 83 4 10 66 113 4 34 73 Grease 5.Apply a small amount of grease to the axle on the Left Crank Arm (34). Identify the Left Pedal Leg (4), which is marked with an “L” sticker. Slide a Pedal Leg Spacer (73) and the Left Pedal Leg onto the axle on the Left Crank Arm (34). (Note: It may be helpful to use a rubber mallet to tap the Left Pedal Leg on. Do not to confuse the Left Pedal Leg with the Right Pedal Leg [not shown].) Attach the Left Pedal Leg with an M8 x 19mm Patch Screw (111), an M8 Washer (66), and a Torque Washer (113). Attach the Right Pedal Leg (not shown) in the same way. See the inset drawing. Identify the Left Pedal (10), which is marked with an “L” sticker. Attach the Left Pedal to the Left Pedal Leg (4) with two M6 x 48mm Flat Head Screws (83). Note: The Left Pedal can be attached in any of three positions using the three sets of holes in the Left Pedal Leg. Attach the Right Pedal (not shown) to the Right Pedal Leg (not shown) in the same way. 6.Hold a Pedal Wheel (28) inside of the bracket on one of the Upper Body Legs (31). Hold the Upper Body Leg and the Pedal Wheel inside of the bracket on the Left Pedal Leg (4). Slide a Pedal Leg Cover (33) onto the long side of an M8 x 63mm Bolt Set (65), and insert the Bolt Set into the Left Pedal Leg, the Upper Body Leg, and the Pedal Wheel. Slide a Pedal Leg Cover (33) onto the short side of the M8 x 63mm Bolt Set (65) and tighten it into the long side of the Bolt Set. Attach the other Upper Body Leg (not shown) and the other Pedal Wheel (not shown) to the other side of the elliptical exerciser in the same way. 5 6 33 31 65 65 33 28 4 8 8.Have another person hold the Left Handlebar (24) near the Upright (2) as shown. Connect the left Pulse Sensor Wire (20) to the Pulse Extension Wire (101). Slide an Axle Cover Endcap (91) onto the lower end of the Left Handlebar. Slide the upper end of the Left Handlebar (24) into the tube on the front of the Upright (2), while sliding the lower end of the Left Handlebar onto the Arm Axle (19). Attach the upper end of the Left Handlebar with two M8 x 42mm Button Bolts (85) and two M8 Nylon Jam Nuts (86); be careful not to damage the Wires (20, 101) as you insert the Button Bolts. Make sure that the Jam Nuts are resting in the hexagonal holes in the tube on the front of the Upright. Attach the lower end of the Left Handlebar with an M8 x 35mm Button Bolt (105) and an M8 Jam Nut (86). Press the tabs on the Axle Cover Endcap (91) into the left Axle Cover (26). Attach the Right Handlebar (23) to the Upright (2) in the same way. Hold the halves of the Handlebar Cover (25) around the tube on the front of the Upright (2); be careful not to damage the Wires (20, 101). Attach the Handlebar Cover with an M4 x 16mm Round Head Screw (96). 24 20 101 9...