Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Wipe Down / Cleaning To prevent the build-up of rust and other forms of corrosion, wipe down the cycle at the end of each day (or preferably at the end of each class). Raise all posts to the highest setting to expose moisture. Using an absorbent cloth, focus on all areas that perspiration can settle. Give particular attention to the following areas: o Handlebar o Seat / adjustable slide for the seat o Flywheel o Back leg assembly o Chain guard o Brake knob and bolt assembly o Pop-pins o Leveling feet NOTE: Never use abrasive cleaning liquids or petroleum-based solvents when wiping down the cycle. NOTE: It is recommended that class instructors direct class participants to release all the tension from the cycle at the end of each class to allow perspiration to evaporate. Inspection / Adjustment Inspect major moving parts that require constant proper torque. Loose or misadjusted parts can result in personal injury or damage to the cycle. Check the following parts for security and/or proper torque. Crank arms Use a foot pound torque wrench, tighten to 30 - 35 foot-pounds. Pedals Use a pedal wrench. Verify that the pedal is not cross-threaded. Page 17 STAR TRAC GROUP CYCLES OWNER’S GUIDE IMPORTANT: If your facility allows members to interchange pedals, it is critical that the pedals are checked after each class to prevent damage, which may lead to injuries if ignored. Water bottle (V-bike & Spinner Pro) Tighten down assembly screws. NOTE: Water bottle cages are easily damaged when oversized bottles are forced to fit within the bottle cage. Checking and tightening the screws will help prevent damage. WEEKLY MAINTENANCE Weekly maintenance should focus on the overall performance of the group cycle. During these inspections, look for vibration and possible loose assemblies. Have an experienced rider ride each cycle to identify and help diagnose any vibration, noises, and any "unusual" feeling from the drive chain. Either faulty flywheel alignment or a loose chain can cause vibration. o Check for proper flywheel alignment. Torque flywheel nuts as necessary. o Remove chain guard and check for loose chain. Adjust chain as necessary (refer to "Chain Adjustment" on page 14). o Inspect The Bottom Bracket Assembly (BBA). The BBA will come loose periodically and require tightening. Loose play (left and right motion) indicates the BBA needs adjusting. (V-bike only) Inspect each cycle for loose assemblies, parts, bolts and nuts. Give particular attention to the following: o Tighten all frame base hardware. o Tighten all pull pin handles. o Tighten seat hardware. o Tighten pedal toe clip / toe straps. o Inspect and tighten tension knob assembly. MONTHLY MAINTENANCE The monthly maintenance check should be a comprehensive inspection of the overall frame and main assembly components of the group cycle. Inspection Inspect the frame and main assembly components for rust or corrosion. Tilt the cycle or place in an upside down position to locate areas where rust and corrosion may develop. Use a small, wire brush to remove rust build-up in small crevasses, such as leveling feet, pop pin handles and other bolt assemblies. Give particular attention to the following areas: o Leveling feet o Pop pin handles Inspect all wear items for adjustments or possible part replacement. Give particular attention to the following: o Inspect brake pad for wear. Excessive wear, such as glazing or leather separation, indicates replacement is required. o Inspect seat pad for wear. Rips, tears or excessive movement indicates replacement is required. o Inspect pedals for play. Excessive movement of pedals indicates replacement is required. Page 18 STAR TRAC GROUP CYCLES OWNER’S GUIDE MOVING AND LEVELING To move the cycle to a new location: Lift the cycle from the rear and use the front wheels (located on the front leg, below the handlebar) to roll the cycle from one location to another. To level the cycle: Use the four leveling adjusters (located on the underside of the front and rear legs) to compensate for uneven floor surfaces. PARTS REPLACEMENT BRAKE PAD REPLACEMENT Removal 1. Remove tension from the brake pad by turning the Push Brake System knob counterclockwise, until completely loose. 2. Using the Multi-Purpose Wrench, remove the two bolts supporting the brake pad onto the frame ). Installation 1. Carefully re-install the two bolts through the brake pad bracket onto the frame. Tighten by using the Multi-Purpose Wrench. Page 19 STAR TRAC GROUP CYCLES OWNER’S GUIDE Chain tension adjustment NXT PRO/ ELITE 1. Using the 16mm or 5/8” socket and socket wrench loosen the axle nuts on the sides of the flywheel. 2. Using the 10mm open end wrench, loosen the lock nuts on the chain adjustment screws. 3. To tighten the chain, turn the adjustment screw in a clockwise rotation equally on both sides using the 10mm open end wrench. 4. To loosen the chain turn the adjustment screw counter clockwise rotation (unscrew) equally on both sides using the 10mm open end wren...
Otros modelos de este manual:bicicletas - 6800 (1.48 mb)
bicicletas - 6900 (1.48 mb)
bicicletas - 7000 (1.48 mb)