Please fasten the drain hose to the drain thread of safety valve by twisting (see to Figure 3). Connect the other end of drain hose to the sewer to avoid polluting the room by splashing. When the power is switched on, and the water heater starts operating, there may be some water discharged from the pressure relief hole of safety valve. It is due to the water expansion under heating, and is normal phenomenon. The pressure relief pipe shall communicate with the air directly.Do not Connect to drai

The information in this publication was derived from various sources, is provided in good faith and believed to be correct when published. Products listed in this publication are provided for the purposes of information only and reference in this publication should not be construed as an official endorsement by any of the government agencies participating in the Reach for the Stars Program. This document can be made available in alternative formats to meet the needs of people with disabilities.

Haier products have good quality and excellent performance.To facilitate you to use the product, please read the manual and operate accordingly.Please retain it for future reference. The international star service of Haier Group will always accompany you.No matter what kind of problems you meet in usage,please contact with the local after-sales service agent.We are at your service all the time.Thanks again for choosing Haier Product. The water heater you purchased may not full comply with the ma

Electric water heater shall be located in a place easy for use, maintenance and with a floor drainer. In case the tank or pipes leak, nearby or lower facilities shall not be damaged. The installation location shall avoid being above toilet bowl, bathtub, washbasin or doorframe, where will cause a suppressed or unsafe feeling to users. Power socket for water heater shall be in a dry place free of water splash. (splashproof box is preferred). Do not confuse inlet and outlet water pipes. Safety val

This water heater shall only be repaired and maintained by qualified servicemen. Improper maintenance may cause severe injury or damage. Before opening or repairing water heater, please do pull out the power plug. External Cleaning: Disconnect power supply before cleaning. Gently wipe with wet cloth dipped with a little of mild detergent. Do not use gasoline or other solvents. Finally dry with dry cloth. Keep water heater dry. Do not use cleansers containing grinding agent (e.g. toothpaste), aci

• Securing the bracket 1. Recommend you to secure the legs of the water heater on a foundation with embedded irons. You can also make cement bricks, attach expansion bolts in the cements and fix the heater legs on the expansion bolts. 2. Adjust the height of the bracket using the hard, waterproof spacers to ensure levelness of the water tank as well as even the load of each leg. Notes: 1. Ensure close contact of all legs of the water heater with the support plane. No legs are allowed to hang in

2. Effective and energy-saving heat insulation layer Polyurethane foam material for solar water heater is adopted to ensure high heat insulation ability and reduce heat loss to the maximum extent. 3. Al-Zn alloy coated tank shell Al-Zn alloy coated steel plate has very strong anti-corrosion ability and excellent weatherability. It is the most preferred outdoor protective material. 4. Tower type bracket The bracket is made of carbon steel panel by shaping and plastic spraying. It has the advantag

Vent Overflow Water inlet and outlet Tap water Check valve Operation instructions • FAQ Troubles Possible reasons Solutions No outlet water The water tank becomes empty Add water according to the time required in the instruction manual Disconnection or blockage of the pipeline or joints Repair the pipeline or remove the blockage No water comes from the overflow Broken vacuum tube(s) Replace the broken tube(s) pipe Water supply is stopped or water pressure is too low Wait until the water supply b

China Group Qingdao Economic and Technological Development District Haier Water Heater Co., Ltd. Contents Before usage Installlation FAQ Features Installation FAQ Parameters Dimensions Packing list Electric circuit diagram 5 See to the physical product for the appearance, color or pattern. Packing List Expansion hook (pcs) User's manual (copy) Electric water heater (set) Safety valve (pcs) Expansion bolt (pcs) Drain hose (ply) Quantity Name Safety precautions Setting environment Attentions in in

The hose can be cut short or extended as necessary. To avoid splash, the hose shall be installed as inclined downward. Fix the showerhead holder at a suitable place on the wall, and place the showerhead on the holder. After making sure the tank is full of water, connections show no water leakage and power supply complies with requirement, connect the power supply and make trial operation. (Fig.4) (Fig.5) Pressure Relief Vent During installation, adequate space must be reserved for future mainten