|
Resumen del manual
Do not use abrasives or oven cleaners. Rinse, shake and let them dry before replacing. They may also be cleaned in an automatic dishwasher. To remove: Grasp the baffle knobs and pull them up, forward and out. Grasp the drip tray and carefully lift it up and out of the hood track. To replace the drip trays: 1. Place and seat the drip tray into the hood track. 2. Slide them left or right until all trays are side-by-side in place in the track. To replace the baffles: 1. Hold the baffle at the bottom by one of the knobs . 2. Place the other end of the baffle against the inside front of the hood. 3. Slide it up and push the bottom end back until it firmly seats into place. Drip Tray Drip Tray Track Drip Tray Replacement Baffle Baffle Replacement Care and Cleaning Professional Range Hood Do not use a steel-wool pad; it will scratch the Stainless surface. steel surfaces (on some 1. Shake bottle well. models) 2. Place a small amount of CERAMA BRYTE® Stainless Steel Cleaning Polish and Conditioner on a dry cloth or dry paper towel. 3. Clean a small area (approximately 8. x 8.), rubbing with the grain of the stainless steel if applicable. 4. Dry and buff with a clean, dry paper towel or soft cloth. 5. Repeat as necessary. To order: To order CERAMA BRYTE® Stainless Steel Cleaning Polish and Conditioner, please call our toll-free number: National Parts Center . . . . . . . 800.626.2002 CERAMA BRYTE® Stainless Steel Cleaning Polish and Conditioner . . . . . . . # PM10X313 Light bulbs The bulbs are located on the underside of the hood. To change the light bulbs: 1. Remove the trim ring by turning it counterclockwise. 2. Grasp the bulb on the edges and remove by turning it counterclockwise. 3. Replace with the same type and size bulb. These 120 volt, 50 watt, par 16 halogen flood bulbs, with standard base, are available at specialty lighting stores. These bulbs can also be ordered from your GE supplier. Order bulb no. WB08X10028. Warming lamps The warming lamps are located on the underside of the hood. These 120 volt, 175 watt, par 38 infrared heat lamp bulbs, with standard base, are available at some specialty lighting stores. These infrared bulbs can also be ordered from your GE supplier. Order bulb no. WB08X10029. NOTE: If warming lamps are not desired, additional cooktop lighting can be obtained by replacing the infrared bulbs with standard incandescent bulbs with up to 100 watt maximum ratings, with standard bases. These bulbs are available at specialty lighting stores. The Problem Solver Professional Range Hood PROBLEM POSSIBLE CAUSE Questions? Use this problem solver! FAN AND LIGHTS DO • The hood was never electrically connected by the installer/ NOT OPERATE WHEN electrician/builder. Call the electrician/installer/builder to THE SWITCHES ARE complete the the installation. This is not covered by warranty. TURNED ON • A fuse may be blown or a circuit breaker tripped. Replace the fuse or reset the circuit breaker. THE BLOWER DOES • The blower motor wire harness was not connected or was not NOT WORK BUT THE connected properly by the installer/electrician/builder to its mating LIGHTS DO connector located inside the hood on the top surface, to the left of the blower assembly. 1. Switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 2. Remove the filters and locate the blower wire harness connector. Is it plugged into its mating connector? 3. If no, plug the blower motor connector into its mating connector on the top of the hood. Switch the power back on. Check to see if the fan now works. 4. If no, check the circuit breaker/fuse. If it is blown/tripped, replace/reset it. Does the blower work now? If no, call GE for service. THE BLOWER FAILS • Many factors could be the root cause for reduced air-flow. TO E...
Otros modelos de este manual:Los aficionados - ZV30 (154.46 kb)
Los aficionados - ZV48 (154.46 kb)