Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
WARNING • This Liquid Propane conversion Kit must be installed only by a qualified service technician. • Gas supply system must be installed in accordance with the U.S. National Fuel Gas Code. • This appliance and its individual shut off valve must be disconnected from the gas supply piping system during any system pressure test in excess of 1/2 PSI (3.5 KPA). • Use a system manual shut off valve to shut off the gas supply to this gas appliance before continuing with installation procedures. Note: These instructions apply to grill Model 8350 Series. The parts included are designed for your specific grill. The illustrations may differ slightly from model to model. WARNING • If the information in this document is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Read the Coleman® Gas Barbecue Use, Care & Assembly Manual With Grill Lighting Instructions,before attempting installation of this conversion kit. WARNING • TURN OFF THE GAS SUPPLY! DO NOT attempt to install this Natural Gas Conversion Kit while the barbecue is in operation or is hot. WARNING A liquid propane tank, not connected for use with this gas barbecue, shall not be stored in the vicinity of this or any other appliance. Installation and provision for combustion and ventilation air must conform with the National Fuel Gas Code, ANSI Z223.1, or CAN/CGA-B149.1, Natural Gas Installation Code, or CAN/CGA-B149.2, Propane Installation Code. Turn off and disconnect from Natural Gas service line prior to servicing grill. Liquid Propane Gas Conversion Instructions 4 5 2 6 1 3 Liquid Propane Gas Conversion Instructions 4 5 2 6 1 3 Item No. Qty Description 1 1 Main Burner Valve & Manifold Assembly (L.P.) 8350 2 1 Main Regulator Hose Assembly (L.P.) 3 1 Rear IR L.P. Orifice (8350) 4 1 Connector 3/8" FNPT x 3/8" MFLR 5 1 Pipe Sealant 6 1 LP Conversion Sticker 2 Liquid Propane Gas Conversion Instructions Tools Needed: Phillips head screwdriver 1/4" nut driver * 9/16" wrench Adjustable wrench * socket set with extension can also be used. Be sure gas supply is off, the knobs are in the off position and the grill is cool. 1. Remove cooking grates and heat tents. (See Fig. 1). 2. Remove the screws holding the rear heat shield in place. Lift out rear heat shield and set aside (Fig. 2). 3. Remove the two screws holding each igniter in place (Fig. 3). 4. Lay igniters on floor of grill (Fig. 4). Fig 4 Fig 1 Fig 2 Fig 3 Rear Heat Shield Screws Heat Tents Screws 3 Liquid Propane Gas Conversion Instructions 5. Remove the screws from the bottom of the heat shield, holding the front heat shield in place. The screws are located under the bottom lip of the shield (Fig. 5). 6. Remove the side heat shield screws located under the bottom lip of the heat shield. Remove all of the top heat shield screws (Fig. 6). 7. Remove the front heat shield (Fig. 7). 8. Grasp and push the burners towards the rear of the grill to detach the burner from the valves (Fig. 8). 9. Angle the burners up and remove (Fig. 8). Fig 5 Fig 6 Side Screws (Repeat on left side) Screws under lip Fig 8 Fig 7 Tabs 4 Liquid Propane Gas Conversion Instructions 10. Disconnect the right side flexline from the manifold using the adjustable wrench. This will free up the right side of the manifold (Fig. 9). 11. Disconnect the left side flexline from the back infrared valve using an adjustable wrench. This will free up the left side of the manifold (Fig. 10). Fig 9 12. Remove the control knobs from the front of the grill (Fig. 11). 13. Remove the two screws holding each bezel in place on the control panel (Fig. 12). 14. Remove the bezels from the front control panel. Note: The small bezel stays in place (Fig. 13). Fig 10 15. Remove manifold from grill body (Fig. 14). Gas Inlet Flex Line Flex Line Manifold Screws Fig 11 Fig 12 Manifold Fig 14 Fig 13 5 Liquid Propane Gas Conversion Instructions You are now ready to install the new LP manifold. 16. NOTE: New screws for the bezels are inserted into the new LP manifold at the factory. Remove them before proceeding with Step 17. 17. Place the new manifold into the grill body with the control knob stems going outward through control panel front (Fig. 15). 18. Reattach the bezels to the manifold with the screws. Make sure that "off" is facing up on the bezel (Fig. 12 & 13). 19. Reattach the control knobs onto the manifold stems, making sure the arrow is facing upwards (Fig. 11). Fig 15 Control Knob Stems Fig 16 Valves Burners 20. Reattach the flexline on the left of the grill to the back infrared valve using an adjustable wrench (Fig. 10). 21. Reattach the flexline on the right of the grill to the new manifold using the adjustable wrench (Fig. 9). 22. Reinstall burners into the grill body. Line up the burners with the valves on the manifold, making sure they are level. Make sure the burners are fully over the valves (Fig. 16). 23. Reattach the igniters and their heat shields (removed in Steps 2, 3, and 4) to the burne...