Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
FIGURE 2. Anchor the base to your patio using the two holes provided in the base. (Hardware not included) Note: Make sure that the large rectangular cut out is facing in the direction that you want your grill to face. FIGURE 2. 8 FIGURE 1 3 7 • Two adjustable wrenches or a socket set • A medium Phillips screwdriver • Pipe thread sealer or Teflon tape (for gas connections) • Soapy water solution (to test for leaks) Attach four .-20 x 4" eyebolts (7) to the bottom of the square post using hex head bolts (5), flat washers (1), lock washers (2), and nuts (3). Figure 1. NOTE: The large rectangular cut out is located at the front of the post near the top. FIGURE 2 Insert the flex tubing into the post. The inlet side of the gas tubing may protrude from the bottom of the patio base or through the large circular hole in the back of the square post. Note: Do not attempt to cut or alter the flex tube in any way. 5 2 1 1 2 3 PATIO BASE POST ASSEMBLY 12 PATIO BASE POST ASSEMBLY 12 THE GRILL MUST BE ISOLATED FROM THE GAS SUPPLY PIPING SYSTEM BY CLOSING ITS INDIVIDUAL MANUAL SHUTOFF VALVES DURING ANY PRESSURE TESTING OF Fasten the four .-20 x 13/4" short eyebolts (4) to THE GAS SUPPLY PIPING SYSTEM AT TEST PRESSURES the top of the square post using hex head bolts EQUAL TO OR LESS THAN ° PSIG. (5), flat washers (1), lock washers (2), and nuts (3). Position the grill head onto the eyebolts and fasten with lock washers (2) and nuts (3). FIGURE 3. FIGURE 3 3 2 4 GRILL BOTTOM 6 12FIGURE 4 WARNING: DO NOT SUPPLY LP GAS TO A GRILL DESIGNED FOR NATURAL GAS OR NATURAL GAS TO A GRILL DESIGNED FOR LP GAS. Arrange with your local gas company to have a gas supply line connected to the inlet of the flex tube. The gas supply must have a shutoff valve inside the wall and must be shutoff when the grill is not in use. Use pipe thread sealant or Teflon tape at the threads of each connection being careful to not allow any of these materials into the flare seat. Test for gas leaks as directed by the grill’s Owner Manual. THE GRILL AND ITS INDIVIDUAL SHUTOFF VALVES MUST BE DISCONNECTED FROM THE GAS SUPPLY PIPING SYSTEM DURING ANY PRESSURE TESTING OF THAT SYSTEM AT TEST PRESSURES IN EXCESS OF ° PSIG. 6 Attach the retainer bracket to the slide with a wing nut as shown by Figure 5. FIGURE 5 99 13 1313 PATIO BASE POST ASSEMBLY 13 PATIO BASE POST ASSEMBLY 13 FIGURE 6 Attach the bracket and slide assembly to the factory installed screw located in the bottom of the grill housing. Figure 6. Loosen the wing nut and move the slide up or down to accept the grease cup. Be sure to trap the rim of the cup as shown. Use only noncombustible containers for the grease cup (aluminum or tin cans) do not use combustible containers such as Styrofoam or paper cups. FIGURE 7 Attach the control housing (10) using two #8 x 1/2 screws (11) or two plastic panel fasteners as shown in Figure 7. 11 11 1010 Continue assembly as directed by the Owner’s Manual packaged with the grill head. U48 AND P48 IN-GROUND POST INSTALLATION INSTRUCTIONS 2 3 1 4 7 5 6 WARNING:THIS IN-GROUND POST IS NOT DESIGNED FOR USE WITH AN LP GAS CYLINDER. WARNING: SEE YOUR GRILL OWNER’S MANUAL FOR PROPER LOCATION, MINIMUM CLEARANCES, AND OTHER IMPORTANT SAFETY INFORMATION BEFORE PROCEEDING WITH INSTALLATION OF THIS INGROUND POST. KEEP THIS OWNER’S MANUAL FOR FUTURE REFERENCE. EMPIRE COMFORT SYSTEMS, INC. • 918 FREEBURG AVE. • BELLEIVLLE, IL 62220 • 618-233-7420 IN-GROUND POST PARTS DIAGRAM 15 IN-GROUND POST PARTS DIAGRAM 15 All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact Broilmaster® Customer Service at (618) 233-7420. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model number of your Side Burner, Part Name, Part Number, and Quantity of parts needed. ITEM U48 PART P48 PART NUMBERPART NUMBER QTY.NUMBER NUMBER 11/4 FLAT WASHER 4HD504 HD504 21/4 LOCK WASHER 8HD582 HD582 31/4-20 HEX NUT 8HD197 HD197 41/4-20x1 3/4" EYEBOLT 4HD170 HD170 51/4-20x3/4" BOLT 4HD125 063096 6STAINLESS STEEL FLEX TUBE ASSEMBLY 1076519 076519 748" POST 1825615P 064573 8CONTROL HOUSING 1896076P 064854 9#8 SCREW/PLASTIC PANEL FASTENER 2HD427 068182 10 MALE FLARE FITTING 1248x6x6 248x6x6 GREASE CUP ASSEMBLY 1 065821 065821 VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED BEFORE BEGINNING THIS INSTALLATION. CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES. WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY. IN-GROUND POST INSTALLATION 16 IN-GROUND POST INSTALLATION 16 The U48 and P48 In-Ground Posts are only for use with Broilmaster® Gas Grills. Before proceeding with installation read your Owner’s Manual for the proper location and minimum clearances to combustible materials for your grill and in-ground post. Verify that all parts listed in the exploded view of this product have been included before beginning this installation. Recommended Tool...
Otros modelos de este manual:Greeley - AND P48 (429.43 kb)