Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Make sure to put taller end at rear of fire box. Insert the two wire ends at rear of warming rack into holes in back of firebox. Front wires of warming rack rest on sides of firebox. 27 22 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill. Secure cylinder with cylinder screw under bottom shelf. Perform Burner Flame Check. See Use & Care section of this manual to perform the "Burner Flame Check" and for important safety instructions before using. Cylinder screw at rear of cart €> a ® Always keep LP cylinders in upright position during use, transport, and storage. t CAUTION t Cylinder valve must face to front of cart once tank is attached. Failure to install cylinder correctly may allow gas hose to be damaged in operation, resulting in the risk of fire. ■ * 23 On back of grill, slide grease tray into opening in upper back panel. t CAUTION t Failure to install grease tray will cause hot grease to drip from bottom of grill with risk of fire or property damage. Grease tray 28 EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking from cracked/cut/burned hose. • Damaged hose. • Turn off gas at LP cylinder or at source on natural gas systems. If anything but burned, replace valve/hose/regulator. If burned, discontinue use of product until a plumber has investigated cause and corrections are made. Gas leaking from LP cylinder. • Mechanical failure due to rusting or mishandling. • Replace LP cylinder. Gas leaking from LP cylinder valve. • Failure of cylinder valve from mishandling or mechanical failure. • Turn off LP cylinder valve. Return LP cylinder to gas supplier. Gas leaking between LP cylinder and regulator connection. • Improper installation, connection not tight, failure of rubber seal. • Turn off LP cylinder valve. Remove regulator from cylinder and visually inspect rubber seal for damage. See LP Cylinder Leak Test and Connecting Regulator to the LP Cylinder. Fire coming through control panel. • Fire in burner tube section of burner due to blockage. • Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After fire is out and grill is cold, remove burner and inspect for spider nests or rust. See Natural Hazard and Cleaning the Burner Assembly pages. Grease fire or continuous excessive flames above cooking surface. • Too much grease buildup in burner area. • Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After cooling, clean food particles and excess grease from inside firebox area, grease tray, and other surfaces. Troubleshooting Problem Possible Cause Prevention/Solution Burner(s) will not light using ignitor. (See Electronic Ignition Troubleshooting also) Continued on next page. GAS ISSUES: • Trying to light wrong burner. • Burner not engaged with control valve. • Obstruction in burner. • No gas flow. • Vapor lock at coupling nut to LP cylinder. • Coupling nut and LP cylinder valve not fully connected. ELECTRICAL ISSUES: • Electrode cracked or broken; “sparks at crack.” • Electrode tip not in proper position. • Wire and/or electrode covered with cooking residue. • Wires are loose or disconnected. • Wires are shorting (sparking) between ignitor and electrode. • Dead battery. • See instructions on control panel and in Use and Care section. • Make sure valves are positioned inside of burner tubes. • Ensure burner tubes are not obstructed with spider webs or other matter. See cleaning section of Use and Care. • Make sure LP cylinder is not empty. If LP cylinder is not empty, refer to “Sudden drop in gas flow.” • For a grill equipped with the AUTO-CLEAN™ feature, make sure the AUTO-CLeAn™ valve is set to “Grill” • Turn off knobs and disconnect coupling nut from LP cylinder. Reconnect and retry. • Turn the coupling nut approximately one-half to three-quarters additional turn until solid stop. Tighten by hand only - do not use tools. • Replace electrode(s). Main Burners: • Tip of electrode should be pointing toward gas port opening on burner. The distance should be 1/8” to 1/4”. Adjust if necessary. Sideburner: • Tip of electrode should be pointing toward gas port opening on burner. the distance should be 1/8” to 3/16”. Adjust if necessary. • Clean wire and/or electrode with rubbing alcohol and clean swab. • Reconnect wires or replace electrode/wire assembly. • Replace ignitor wire/electrode assembly. • Replace with a new AA-size alkaline battery. 29 Troubleshooting (continued) Problem Possible Cause Prevention/Solution Burner(s) will not light using ignitor. (See Electronic Ignition Troubleshooting also) ELECTRONIC IGNITION: • No spark, no ignition noise. • No spark, som...