Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
This indicates a problem with the cylinder and it should not be used on any product. Return to supplier! CAUTION • Putting out grease fires by closing the lid is not possible. Grills are well ventilated for safety reasons. • Do not use water on a grease fire. Personal injury may result. If a grease fire develops, turn knobs and LP cylinder off. • Do not leave grill unattended while preheating or burning off food residue on HI. If grill has not been regularly cleaned, a grease fire can occur that may damage the product. Ignitor Lighting s Do not lean over grill while lighting. 1. 2. 3. 4. 5. Turn OFF gas burner control valves. Turn ON gas source or tank. Open lid during lighting. To ignite, turn IGNITION BURNER knob to HIGH. Push and hold ELECTRONIC IGNITION button. 6. If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. 7. Ignite other burners by turning knob to . If ignitor does not work, follow match lighting instructions. After Lighting: Turn knobs to HIGH position for warm-up. 7 Lighting instructions continued on next page. WARNING Turn controls and gas source or tank OFF when notin use. CAUTION If ignition does NOT occur in 5 seconds, turn theburner controls OFF, wait 5 minutes and repeat thelighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of theburner and could accidently ignite with risk of injury. Match-Lighting s Do not lean over grill while lighting. 1. Open lid. Turn on gas at LP cylinder. 2. Place lit match into match holder (hanging from cart side panel), light burner on right or left side of grill. 3. Push in and turn far right or far left burner knob to HIGH. Be sure burner lights and stays lit. 4. Light adjacent burners in sequence by pushing knobs in and turning to HIGH. Sideburner Ignitor Lighting sDo not lean over grill while lighting. 1. Turn OFF gas burner control valves. 2. Turn ON gas source or tank. 3. To ignite SIDEBURNER, open sideburner cover. 4. Turn side burner knob to . Push and hold ELECTRONIC IGNITION button. 5. If sideburner does NOT light, turn knob to OFF, wait 5 minutes, then repeat lighting procedure. Sideburner Match Lighting 1. Open sideburner lid. Turn on gas at LP cylinder. 2. Place lit match near burner. 3. Turn sideburner knob to . Be sure burner lights and stays lit. Burner Flame Check •Remove cooking grates and flame tamers. Light burners, rotateknobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Perform burner flame checkon sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" inthe Troubleshooting Section. HIGH LOW Turning Grill Off •Turn all knobs to OFF position. Turn LP cylinder off by turning hand-wheel clockwise to a full stop. Ignitor Check •Turn gas off at LP cylinder. Press and hold electronic ignitorbutton. "Click" should be heard and spark seen each timebetween collector box or burner and electrode. See "Troubleshooting" if no click or spark. Valve Check •Important: Make sure gas is off at LP cylinder beforechecking valves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should springback. If knobs do not spring back, replace valve assemblybefore using grill. Turn knobs to LOW position then turn back toOFF position. Valves should turn smoothly. Hose Check •Before each use, check to see if hoses are cut or worn. Replace damaged hoses before using grill. Use onlyvalve/hose/regulator specified by manufacturer. General Grill Cleaning •Do not mistake brown or black accumulation of grease andsmoke for paint. Interiors of gas grills are not painted at thefactory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brushon insides of grill lid and bottom. Rinse and allow to completelyair dry. Do not apply a caustic grill/oven cleaner to paintedsurfaces. • Plastic parts: Wash with warm soapy water and wipe dry. s Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result. •Porcelain surfaces: Because of glass-like composition, mostresidue can be wiped away with baking soda/water solution orspecially formulated cleaner. Use nonabrasive scouring powder for stubborn stains. •Painted surfaces: Wash with mild detergent or nonabrasive cleaner and warm soapy water. Wipe dry with a soft nonabrasive cloth. •Stainless steel surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy waterand wipe dry with a soft cloth after each use. Baked-on greasedeposits may require the use of an abrasive plastic cleaningpad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics. • Cooking surfaces: If a bristle brush is used to clean any ofthe grill cooking surfaces, ensure no loose bristles remain on...