Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
• Fire in burner tube section of burner due to blockage. • Too much grease buildup in burner area. • Turn off gas at LP cylinder or at source on natural gas systems. If anything but burned, replace valve/hose/regulator. If burned, discontinue use of product until a plumber has investigated causeand corrections are made. • Replace LP cylinder. • Turn off LP cylinder valve. Return LP cylinder to gas supplier. • Turn off LP cylinder valve. Remove regulator from cylinder and visually inspect rubber seal for damage. See LP Cylinder Leak Test and Connecting Regulator to the LP Cylinder. • Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After fire is out and grill is cold, remove burner and inspect for spider nests or rust. See Natural Hazardand Cleaning the Burner Assembly pages. • Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After cooling, clean food particles and excess grease from inside firebox area, grease tray, and other surfaces. Troubleshooting Problem Burner(s) will not lightusing ignitor. (See Electronic IgnitionTroubleshooting also) Continued on next page. Possible Cause GAS ISSUES: • Trying to light wrong burner. • Burner not engaged with control valve. • Obstruction in burner. • No gas flow. • Vapor lock at coupling nut to LP cylinder. • Coupling nut and LP cylinder valve not fully connected. ELECTRICAL ISSUES: • Electrode cracked or broken; “sparks atcrack.” • Electrode tip not in proper position. • Wire and/or electrode covered withcooking residue. • Wires are loose or disconnected. • Wires are shorting (sparking) betweenignitor and electrode. • Dead battery. Prevention/Solution • See instructions on control panel and in Use and Care section. • Make sure valves are positioned inside of burner tubes. • Ensure burner tubes are not obstructed with spider webs or othermatter. See cleaning section of Use and Care. • Make sure LP cylinder is not empty. If LP cylinder is not empty, refer to “Sudden drop in gas flow.” • Turn off knobs and disconnect coupling nut from LP cylinder. Reconnect and retry. • Turn the coupling nut approximately one-half to three-quarters additional turn until solid stop. Tighten by hand only - do not use tools. • Replace electrode(s). Main Burners: • Tip of electrode should be pointing toward gas port opening on burner. The distance should be 1/8” to 1/4”. Adjust if necessary. Sideburner: • Tip of electrode should be pointing toward gas port opening on burner. the distance should be 1/8” to 3/16”. Adjust if necessary. • Clean wire and/or electrode with rubbing alcohol and clean swab. • Reconnect wires or replace electrode/wire assembly. • Replace ignitor wire/electrode assembly. • Replace with a new AA-size alkaline battery. • For a grill equipped with the AUTO-CLEAN™ feature, make sure the AUTO-CLEAN™ valve is set to “Grill” Troubleshooting (continued) Problem Possible Cause Prevention/Solution Burner(s) will not lightusing ignitor. (See Electronic IgnitionTroubleshooting also) ELECTRONIC IGNITION: • No spark, no ignition noise. • No spark, some ignition noise. • Sparks, but not at electrode or at fullstrength. • See Section I of Electronic Ignition System. • See Section II of Electronic Ignition System. • See Section III of Electronic Ignition System. Burner(s) will notmatch light. • See “GAS ISSUES:” on previous page. • Match will not reach. • Improper method of match-lighting. • Use long-stem match (fireplace match). • See “Match-Lighting” section of Use and Care. Sudden drop in gasflow or low flame. • Out of gas. • Excess flow valve tripped. • Vapor lock at coupling nut/LP cylinder connection. • Check for gas in LP cylinder. • Turn off knobs, wait 30 seconds and light grill. If flames are still low, turn off knobs and LP cylinder valve. Disconnect regulator. Reconnect regulator and leak-test. Turn on LP cylinder valve, wait 30 seconds and then light grill. • Turn off knobs and LP cylinder valve. Disconnect coupling nut from cylinder. Reconnect and retry. Flames blow out. • High or gusting winds. • Low on LP gas. • Excess flow valve tripped. • Turn front of grill to face wind or increase flame height. • Refill LP cylinder. • Refer to “Sudden drop in gas flow” above. Flare-up. • Grease buildup. • Excessive fat in meat. • Excessive cooking temperature. • Clean burners and inside of grill/firebox. • Trim fat from meat before grilling. • Adjust (lower) temperature accordingly. Persistent grease fire. • Grease trapped by food buildup aroundburner system. • Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position and let fire burn out. After grill cools, remove and clean all parts. Flashback... (fire in burner tube(s)). • Burner and/or burner tubes are blocked. • Turn knobs to OFF. Clean burner and/or burner tubes. See burner cleaning section of Use and Care. Unable to fill LP cylinder. • Some dealers have older fill nozzles with worn threads. • The worn nozzles don’t have enough “bi...