Votos - 0, Puntuación media: 5
(
)
)
|
Resumen del manual
Some cleaning products may harm the finish on the control panel. Wipe the panel dry after cleaning. Wipe the washer cabinet as needed. If detergent, bleach or other washing products are spilled on the cabinet, wipe immediately. Some products will cause permanent damage if spilled on the cabinet. Do not use scouring pads or abrasive cleansers. The washtub will need no particular care though it may need rinsing or wiping after some unusual loads have been washed. This also may be necessary if too little detergent has been used. Leave the lid open to allow the inside of the washer to dry out after use. This helps prevent musty odors from developing. The agitator should not be removed except for service. The washtub is designed to be self cleaning. Replacing Hoses Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to. All hoses should be checked on a monthly basis for any visible signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years. Filter Screens Check the filter screens in the fill hoses for debris or damage annually. Clean or replace them if necessary. If the washer is filling with water slower than normal, check the filter screens. Clean or replace them if necessary. Order filter screen Part No. F270300 from the nearest authorized parts distributor. Reinstallation of Shipping Materials Shipping Brace The shipping brace in the lid opening should be saved and reinstalled whenever the washer is moved. To reinstall the brace, open the washer lid and place the brace over the washer agitator, placing the back of the brace into the lid opening first. Shipping Plug The plastic shipping plug should be saved and reinstalled any time the washer is moved. The plug fits into two openings: The base opening and the shipping plug opening on the bottom of the movable pivot dome. The plug MUST be inserted into both openings to prevent damage to the washer. In order to accomplish this, the shipping plug opening must be directly lined up with the base opening. Refer to Figure 24. TLW2103N 1 Shipping Plug Opening 2 Base Opening 3 Shipping Plug 4 Shipping Brace 2 1 3 4 Figure 24 Motor Overload Protector The internal overload protector will stop the motor automatically in the event of an overload. The overload protector will reset itself in two or three minutes and the motor will restart automatically. If the overload protector stops motor again, remove the washer from use and call the service person to correct the problem. 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 202068 Troubleshooting Try these troubleshooting tips before making a service call. They may save you time and money. Washer Symptom Possible Cause/Solution Won’t Fill • Make sure lid is closed. • Make sure power cord is plugged all the way into the electrical outlet. • Make sure hot and cold water faucets are turned on. • Make sure that the fill hoses are not kinked or twisted. • Place coin(s) in drop or card in reader. • Make sure that the controls are properly set. • Make sure that the last spin has been completed. • Check the laundry room fuse or circuit breaker. • Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. • Water is being siphoned from the washer during the cycle. Refer to the Installation section to make sure that the drain hose has been properly installed. • The motor overload protector may have stopped the cycle. It will reset itself in two or three minutes and restart the washer automatically. Won’t Start • Make sure lid is closed. • Place coin(s) in drop or card in reader. • Make sure power cord is plugged all the way into the electrical outlet. • Make sure that the controls are properly set. • Check the laundry room fuse or circuit breaker. • The motor overload protector may have stopped the cycle. It will reset itself in two or three minutes and restart the washer automatically. Won’t Agitate • Make sure lid is closed. • Place coin(s) in drop or card in reader. • Make sure power cord is plugged all the way into the electrical outlet. • Check the laundry room fuse or circuit breaker. • The motor overload protector may have stopped the cycle. It will reset itself in two or three minutes and restart the washer automatically. • Broken drive belt. Call the service person. • Have a qualified electrician check polarity and grounding. Refer to Electrical Requirements section. Won’t Spin • Make sure lid is closed. • Place coin(s) in drop or card in reader. • Make sure power cord is plugged all the way into the electrical outlet. • Check the laundry room fuse or circuit breaker. • The motor overload protector may have stopped the cycle. It will reset itself in two or three minutes and restart the washer automatically. • Broken driv...