Votos - 1, Puntuación media: 5 ( )

Fabricar: ATON Tamaño del archivo: 382.94 kb Nombre del archivo: Idioma del manual:

This application provides the best sound quality, staging, and depth possible in areas with a defined listening position. Figure 2.1 shows an example of an outdoor stereo listening area. Figure 2.1 - Stereo Application Mono/DVC In many instances, mono or DVC setup will provide a better listening experience in outdoor areas. Mono applications combine the left and right signals to provide the full sound of a piece of music to each speaker in the system without left/right separation. DVC applications send the left signal to one voice coil and the right signals to another voice coil, essentially creating a stereo pair in one speaker cabinet. Use mono or DVC setups for any area that does not have a defined listening area. Area A Area B Figure 2.2 - Mono/DVC Application Page 2 ©2007 • All rights reserved. LEFTSPKPlastic BagLabel Figure 3.1 - Wiring Label & Plastic Bag respectively. Each stereo method can also be used for mono or DVC applications. A/V Receiver/Amplifier • Two separate 2 conductor speaker wires run from the A/V Receiver or amplifier to each stereo speaker. + - + - + - + - Figure 3.2 - Wiring: Amplifier to Speakers-2 Conductor Direct • One 4-conductor speaker wire runs from the amplifier to a splice near one speaker. A 2-conductor wire runs from the splice to each speaker. A/V Receiver/Amplifier + - + - + - + - Splice 4 Conductor Wire 2 Conductor Wire Figure 3.3 - Wiring: Amplifier to Speakers-4 Conductor to 2 Conductor Storm Series Outdoor Speakers Volume Control • One 4 conductor speaker wire runs from the amplifier to a stereo volume control, then one 2 conductor speaker wire runs to each stereo speaker. + - + - + - + - A/V Receiver/Amplifier 4 Conductor Wire 2 Conductor Wire Figure 3.4 - Wiring: Amplifier to Speakers w/ Volume Control • Use any of the stereo wiring methods to connect to a DVC speaker. This example shows 2 separate 2 conductor speaker wires run from the amplifier to the DVC speaker. + - + - + - + - A/V Receiver/Amplifier Figure 3.5 - Wiring: Amplifi er to Speaker-DVC • Use any of the wiring methods to connect to a mono speaker. This example shows a 2 conductor speaker wire running directly from the amplifier to the mono speaker. + - + - A/V Receiver/Amplifier Figure 3.6 - Wiring: Amplifi er to Speaker-Mono Note 1: Low voltage wiring must be run in accordance with the National Electrical Code as well as any other applicable provisions of the local building codes in your area. In some cases (such as commercial installations), running the wire in conduit may be required. If you have any questions concerning the wiring of speakers in your home, contact your local building and inspection department. Note 2: It is recommended that you use quality CL-2 or CL-3 rated stranded speaker wire when installing ATON speakers. Solid-core “Romex” type wire is not acceptable! Use at least 16AWG speaker wire for runs up to 100 feet, and at least 14 AWG speaker wire for runs up to 200 feet. If you must cross high-voltage lines, always do so at a 90 degree angle to avoid audible hum through the speakers!. Note 3: When pre-wiring for outdoor speakers, it is essential to make direct wire runs from the head-end to each speaker. Do not run speaker wires in series or parallel, and do not “daisy-chain” speakers to common wiring. There are instances where speakers will be connected directly to an amplifier. The use of spade lugs or bannana plugs is recommended in these instances. Page 4 ©2007 • All rights reserved. Storm Series Outdoor Speakers Mounting Use the included Mounting Brackets to securely mount the speakers in the desired location. To install the brackets on wood surfaces, vinyl siding, etc.: 1. Place brackets in desired location. 2. Mark location of holes at the narrow point of the keyhole cutout. 3. Drill pilot holes.. 4. Partially tighten screws. 5. Place the brackets in position, then tighten the screws. Screw Location Figure 3.7 - Screw Location To install the brackets on brick or concrete surfaces: 1. Place brackets in desired location 2. Mark location of holes at the narrow point of the keyhole cutout 3. Drill holes using a masonry drill bit. 4...

Descargar ahora

Introduzca dos números de la imagen: