Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Using a receiver or amplifier stronger than that indicated above, you risk blowing either the amp or your speakers, moreover possible fire. If equipment is damaged in any way or unexpected trouble occurs during playback, unplug the system from its outlet and call a serviceman for help. Be sure to reduce the volume level from the receiver when the signal input exceeds the rated allowable input in order to avoid damage to circuitry, or malfunctions. 1. Avoid locations such as described below. • Where exposed to direct sunlight • Near heating appliances or other sources of heat • Where the humidity is high 2. Do not touch the diaphragms. This may cause distortion. Clean the cabinet, panel and controls with a soft cloth lightly moistened with mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. 3 Positioning the speakers To diagram below shows the basic positioning of each speaker. To prevent damage to the speakers, lay them on top of a soft cloth before attaching the speaker feet. • The subwoofer can be placed in any position as long as it is at a reasonable distance from the TV. • Do not place any object on top of the speakers. The front speakers, center speaker and subwoofer are made so they can be used in close proximity of a TV, but irregular coloring may result due to how the system is placed. If such distortion occurs, turn off the TV for sometime between 15 and 30 minutes. The demagnetizing function of the TV will eliminate the distortion. If the irregular coloring still visible, then move the speakers further away from the TV. Please note that if there is a magnetic, object near the TV, irregular coloring may result due to the interaction between the TV and the speaker. Only for surround speakers The methods of installation for each speaker are the same. Caution The wall has to be strong enough to hold a speaker, so it is recommended that you consult a constructor. Please note that if the wall is not strong enough, it may result in a dangerous accident. How to install the metal wall mounts Subwoofer For SB-HT250 For SB-HT210 (included) How to install the speakers on the wall Wall Screw (not ---included! Screw the wood Wall or pillar screw into a thick and hard part of the wall. Consult your dealer for details. ■I Connections 1 Before making the connections, switch OFF the power to the receiver. 1 Be sure to connect only positive (+) wires to positive (+) terminals, and negative (-) wires to negative (-) terminals. Speaker cable (Included) (+) ^ . ./?> (+) .. - (_} Speaker cable connections (rear panel of speakers) -bJ—^ IJHfSi To prevent damage to circuitry, never short-circuit positive (+) and negative (-) speaker wires. NO! Surround speaker (right) Surround speaker (left) Stereo receiver Center speaker Long type “S3 0 es ir o© o© 0 o® 0© © o© o o© © © © © For SB-HT210 Subwoofer Stereo receiver “0 © © w o© o© o o® o© © o© © © o o© © © FRONT CENTER 59 CD WOOFER J > Short type OUTPUT TO FRONT SPEAKER INPUT FROM AMPLIFIER R Front speaker (right) Front speaker (left) Short type 5 Connections For SB-HT250 Speaker cable [pin plug type] (included) Stereo receiver "0 IS © nr 0® 0® 0 0 © 0® ® 0® 0 0 ® ® ® SUB-WOOFER’ ® ® SURROUND FRONT HP CENTER (SI CD Front speaker (right) Short type Subwoofer FROM RECEIVER +■ R - - L + + R - - L -I TO SPEAKER INPUT L@‘- OOO D a Front speaker (left) Connect this cord after other cables are' connected. Household AC outlet (AC 120 V/60 Hz) To connect the front speakers to the subwoofer Speaker cables (sold separately) Stereo receiver 0® 0® 0 0® 0® © 0® ® ® 0 0® ® ® Household AC outlet (AC 120 V/60 Hz) 6 Operation (for Subwoofer) CEgEHSlI POWER indicator 342 1 STANDBY RED V) FROM RECEIVER FBOIBBSVS?! + R _ - L ♦ awwpaan KVi + R- -L< TO SPEAKER POWER ON OFF AC IN 120V-60Hz 60W Set the low pass filter, volume and phase to suit characteristics of the front speaker and subwoofer combination. 7 Set POWER to the “ON” position. (The POWER indicator will light up green.) 2 Set LOW PASS FILTER to a suitable frequency, referring to the “Frequency response by LOW PASS FILTER setting” on the right. [Recommended position for this system : 150 Hz] 3 Set VOLUME to a suitable level, referring to the “Frequency response by VOLUME setting” on the right. IRecommended position for this system : Q (Mark is to 10:00.)] 4 Listen to some music and set PHASE to “NOM” or “REV”, whichever makes playback normal. IJBTS1 If subwoofer and speaker phase are the inverse of one another, they will tend to rub each other out. Playback will not be normal and sounds will seem muffled. About the POWER indicator This unit will automatically go on standby (indicator turns red), if no signal is sent within (approximately) 10 minutes from the moment you turn ON the power. Once t...