Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Curtains or similar materials can be used to prevent these reflections. • To prevent possible acoustic feedback, the speaker systems should be kept away from the turntable. This feedback (howling) can result from vibrations from the speakers. The turntable should, therefore, never be placed on the same surface as the speaker system. A thick piece of felt or similar materia! can be used under the turntable to reduce howling. Closing the turntable’s cover also reduces this problem. Connecting the speaker system Before connecting the speaker systems to the amplifier, please check the following: • Be sure to switch OFF the power to the amplifier. • Use with an amplifier having 80 or below impedance speaker terminals. • Be sure to only connect positive {+) wires to positive {+) terminals, and negative (-) wires to negative (-) terminals. Speaker connection cables (not included) 15 mm Note: To prevent damage to circuitry, never short-circuit positive ( + ) and negative (—) speaker wires. 1. Twist the core of the connection cables. 2. Press the pushbutton, and insert the core until it can no longer be seen. 3. Release the pushbutton, and pull the cable gently to be sure that it is secured. Power-handling capacity The power-handling capacity of this unit is indicated in the specifications. The amplifiers volume control should be set to avoid an excessive input level. This is especially true on amplifiers having an output power rating higher than that of the speaker system. Even if the amplifier to be used has an output power rating lower than that of the speaker system, the amplifier output may become distorted. This’'clipping" distortion creates an excessive input level which can damage the speaker system. This type of distortion also occurs if the input signal to the amplifier is too large. Bass and treble controls also raise the level of the input signal to the speaker system so care should be taken to adjust the volume to a proper level. The volume level of the amplifier should be reduced if the following signals are to be applied to the speaker system: interstation noise of the FM radio band; output from a tape deck during rewind or fast forward; acoustic feedback from a microphone or musical instrument; electrical noise from the connection or disconnection of a phono cartridge, or phono / RCA cables. This unit incorporates protection circuitry that automatically reduces the tweeter level when a safe overall input level has been exceeded. When the protection circuit is activated, the sound from speakers will be interrupted. If the sound is interrupted, do not operate the system continuously. Proceed as follows: 1. Reduce the volume setting of the amplifier. 2. Check whether or not there is any abnormal condition of the equipment used as the sound source, or of the connections. 3. If there is no abnormal condition, the protection circuitry will be automatically reset in a few minutes. After the protection circuit is reset... Do not increase the amplifier's level too high. protection 3 Maintenance Although the enclosure and the speaker units of this speaker system are made of carefully selected materials and have been produced using the finest manufacturing techniques, sudden changes in surrounding temperature and /or humidity should be avoided. Keep this unit away from sources of heat, high humidity and direct sunlight. • The speaker system should not be placed near a TV. The speaker magnet may cause a disturbance in the TV picture. • If the enclosure becomes dirty, use a soft, dry cloth to wipe it clean. If the dirt is excessive, soak a soft cloth in a weak solution of soap and water, wring it thoroughly before use. A soft dry cloth should then be used to wipe it dry. • Never use alcohol, paint thinner, benzine or other volatile chemicals to clean this unit because they may damage the finish, causing it to lose its luster. Also never use a wet or chemically-impregnated cloth. Specifications Not?: Specifications are subject to change without notice. Weight and dimensions are approximate. Typo Speakers: Woofer Midrange Tweeter Input power Sound pressure level Impedance Frequency range Crossover frequencies Circuit protection Dimensions (W x H x 0) Weight SB-LB910 3 way, 3 speaker system Bass-reflex 15" (38cm) cone type 4" (Юст)сопе type 2*9/16* (6.5cm) cone type 200W (music), 100W DIN 90dB/W /m 8 ohms 31Hz - 22kHz (-16dB) 39Hz ~ 20kHz (-1 OdB) 3kHz, 6kHz Yes 18-1/2" X 32-9/32" X 12-27/32" (470 X 820 X 326 mm) 35.7 lb. (16.2kg) Product service Do not attempt to remove the cover(s) or repair the unit yourself. Refer servicing to qualified personnel only. Product Information For product service, product Information or assistance in product operation, refer to the servicenter directory. For detailed instmctions, contact an authorized servicenter in the U.S.A. at 1-800-332-5368 or visit our \Neb site, (http^/ Panasonic Consumer Electronics ...