Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Owner’s Record The model number and serial numbers are located at the rear. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. SA-W305/W303 Serial No. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. CAUTION Use of this appliance with some systems may present a shock or fire hazard. Do not use with any units which have the following marking located near output. WARNING: HAZARDOUS ENERGY! Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For detailed safety precautions, see the leaflet “IMPORTANT SAFEGUARDS” included with this manual in the vinly bag. Welcome! Thank you for purchasing the Sony Active Super Woofer. Before operating this woofer, please read this manual thoroughly and retain it for future reference. TABLE OF CONTENTS Getting Started Unpacking 4 Installation 4 Hooking Up the System 5 Basic Operations Listening to the Sound 8 Adjusting the Sound 9 Additional Information Precautions 10 Troubleshooting 10 Specifications 11 Getting StartedGetting Started Getting StartedGetting Started Unpacking Installation Check that you received the following items: • Audio connecting cord (1) • Speaker cord (2) Since the human ear cannot detect the direction and position where the bass sound being reproduced by a woofer (below 150 Hz) comes from, you can install the woofer wherever you like in your room. To obtain a better bass reproduction, we recommend you to install the woofer on a solid floor where the resonance is unlikely to occur. You can obtain a sufficient heavy bass reproduction from a single woofer. However if you use a couple of the woofers, you can obtain an even more effective heavy bass reproduction. Notes • Always install the woofer vertically, keeping a few centimeters from away the wall. • Do not place an object on the woofer or sit on it. • If the woofer is installed in the center of a room, the bass could be extreamely weakened. This is due to the influence of the standing wave of the room. If this happened, move the woofer away from the center of a room or eliminate the cause of the standing wave, by installing a bookshelf on the wall, etc. 4 Getting Started Getting Started Hooking Up the System Overview Use the LINE IN jack or the SPEAKER IN terminals of the woofer when you connect the amplifier. • If your amplifier has one of the following types of output jacks, connect the LINE IN jack and the amplifier's jack using the supplied audio connecting cord. — MONO OUT jack — MIX OUT jack — SUB WOOFER output jack(s) — SUPER WOOFER output jack(s) • If your amplifier does not have the above mentioned output jacks, connect the speaker terminals of the amplifier to the SPEAKER IN terminals instead. LINE IN SPEAKER IN LINE SPEAKER IN OUT IN + + – – + + – – OUT LRLR Before you get started • Turn off the power of the amplifier and the woofer before making any connection. • Use the audio connecting cords that are supplied to the respective equipment. If there are not enough audio connecting cords to make the necessary connections, you need to purchase some optional audio connecting cords. • Be sure to make connections firmly to avoid noise. • Connect the AC power cord from the woofer to a wall outlet. • You cannot connect the CENTER output jack for use with Dolby Pro Logic function to the woofer. Bass sound is not output with some Dolby Pro Logic modes. (continued) Getting Started Getting Started Connecting to an amplifier with a single set of speaker terminals If your amplifier is equipped with a single set of speaker terminals, connect the woofer to the amplifier, and then connect the front speakers to the woofer. What cords will I need? Speaker cord (supplied) (1 for each speaker) Twist the stripped ends of the cord about 2/3 inch (15 mm). Be sure to match the speaker cord to the appropriate terminal on the componentes: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass. It is useful to decide that the speaker cord marked with a line is always the positive (+) and should be connected to the positive (+) terminal to avoid any improper connections. Hookups 1 Connect the woofer to the amplifier. Connect the SPEAKER...