Fabricar: Sony
Tamaño del archivo: 62.84 kb
Nombre del archivo: 4246665411.pdf
|
Otros manuales para este modelo:
Resumen del manual
And don’t place lighted candles on the apparatus. To prevent fire or shock hazard, do not place vases on the apparatus. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment. About this manual The instructions in this manual are for SA-VE145, Sony Micro Satellite Systems. The SA-VE145 is a 5.1 channel speaker system consisting of two front speakers, two surround speakers, one center speaker, and one subwoofer. It supports Sony Digital Cinema Sound, Dolby* Pro Logic, and Dolby Digital, and is thus gearedtowards the enjoyment of movies. * Manufactured under license from Dolby Laboratories. DOLBY, the double-D symbol ;, “PRO LOGIC” and “Dolby Digital” are trademarks of Dolby Laboratories. A C Subwoofer Center B Front (Right) Front (Left) Center e E A eEEeEeEeEeEeEeEeR INPUT WOOFER OUT FRONT CENTER REAR R L L Surround (Right) Surround (Left) Amplifier 3.5 m 10 m10 m 3.5 m Eee E e Front (Left) Front (Right) E 3.5 m A Subwoofer Surround (Right)Surround (Left) BB Precautions On safety • Before operating the system, be sure that the operating voltage of the system is identical with that of your local power supply. • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Unplug the system from the wall outlet if it is not to be used for an extended period of time. To disconnect the cord, pull the cord by grasping the plug. Never pull the cord itself. • Should any liquid or solid object fall into the system, unplug the system’s power cord and have the system checked by qualified personnel before operating it any further. • AC power cord must be changed only at the qualified service shop. On operation • Do not drive the speaker system with a continuous wattage exceeding the maximum input power of the system. • If the polarity of the speaker connections are not correct, the bass tones will be weak and the position of the various instruments obscure. • Contact between bare speaker wires at the speaker terminals may result in a short-circuit. • Before connecting, turn off the amplifier to avoid damaging the speaker system. • The speaker grille cannot be removed. Do not attempt to remove the grille on the speaker system. If you try to remove it, you may damage the speaker. If you encounter color irregularity on a nearby TV screen This speaker system is magnetically shielded to allow it to be installed near a TV set. However, color irregularities may still be observed on certain types of TV sets. If color irregularity is observed... cTurn off the TV set once, then turn it on again after 15 to 30 minutes. If color irregularity is observed again... cPlace the speakers further away from the TV set. If howling occurs Reposition the speakers or turn down the volume on the amplifier. On placement • Do not set the speakers in an inclined position. • Do not place the speakers in locations that are: —Extremely hot or cold —Dusty or dirty —Very humid —Subject to vibrations —Subject to direct sunlight • Use caution when placing the speaker on a specially treated (wax, oiled, polished, etc.) floor, as staining or discoloration may result. On cleaning Clean the speaker cabinets with a soft cloth lightly moistened with a mild detergent solution or water. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. The volume level should not be turned up to the point of distortion. If the volume level is too high, the speaker protection circuit activates, and the sound level drops suddenly. This is not a malfunction. In this case, lower the volume level and wait for a few moments until the unit resumes normal operation. If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer. Hooking up the system Connect the speaker system to the speaker output terminals of an amplifier. (A) Make sure power to all components (included the subwoofer) is turned off before starting the hook-up. Notes (B) • Make sure the plus (+) and the minus (–) terminals on the speakers are matched to the corresponding plus (+) and minus (–) terminals on the amplifier. • Be sure to tighten the screws of the speaker terminals securely as loose screws may become a source of noise. • Make sure all connections are firm. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. • Do not connect the subwoofer to the amplifier’s CENTER output terminal (which is for Dolby Pro Logic or Dolby Digital). No bass sound will output from the subwoofer if you do. • For details regarding the connections on the amplifier side, refer to the manual that was provided with your amplifier. Tip All striped...
Otros modelos de este manual:- ()