Votos - 4, Puntuación media: 3.8
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
• Secure placement or installation is the owner’s responsibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speakers. • Any time you note distortion, reduce the volume of your amplifier immediately. Make sure the input power does not exceed the specified maximum input power, otherwise the speakers will be damaged. • Do not attempt to clean the speakers with chemical solvents as this might damage the finish. Use a clean, dry cloth. • Do not attempt to modify or fix the speakers. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. Note: This speaker is magnetically shielded, but placing them too close to a TV may impair the TV picture. If this happens, move the speaker away from the TV. DeutschFrancais EspanolEnglish E-1 Precautions When Positioning the Speakers The speaker is constructed with the majority of the weight located in its upper portion, and is thus susceptible to falling over if proper care is not taken to insure its stability. If the speaker falls over, it may damage the speaker or be the cause of injury (or even death) to persons and/or damage to personal property. ¦ For safe and proper use of the speaker: • Position the speaker in a location that is solid, level, smooth, and low (with respect to the floor). • Do not push or apply pressure to the side of the speaker when moving, or lean objects against the side of the speaker. • Do not sit on or set objects on top of the speaker. Vibrations or jolts associated with earthquakes and other phenomena or activities may cause the speaker to fall over. For safety reasons, using commercially available products that increase stability in the speaker is recommended (metal fittings or chains, etc.). Supplied Accessory • Speaker cable (4 m) . 1 Placing the Speakers Place the speakers on a sturdy, vibration-free surface. ¦ Using as Normal Stereo Speakers To get the best stereo performance, angle the speakers inward so as to create a triangle, with the listener at the apex. ¦ Using as Front Speakers in a Surround Sound System Position the speakers both side of your TV. The positioning of these speakers is important because they provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equidistant from the TV. Subwoofer Surround L Center Surround R NS-125F Connecting Your Speakers Always turn off your amplifier or receiver before making any connections. ¦ Preparing Your Speaker Cables Carefully remove 10 mm (3/8 ”) of insulation from both ends of your speaker cables and twist the bare wires tightly, as shown. 10 mm (3/8 ”) Good No Good ¦ Hookup SPEAKERS A B LR ++ – – + – Loosen Tighten Amplifier or receiver Notes: • Make sure that the bare wires are not touching each other as this could damage the speaker and amplifier. • Connect one speaker to the left terminals of your amplifier, and another speaker to the right terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. ¦ Using a Banana Plug 1 32Banana Plug 1. Remove the speaker terminal cover by gently pulling it toward you. 2. Tighten the terminal knob. 3. Simply insert the banana plug into the terminal. English E-3 Removing the front cover Specifications The front cover, which is attached to each speaker at six points, can be removed if desired. To remove a cover, using both hands, gently pull the top of the cover away from the speaker. When the cover comes away, gently pull the bottom of the cover away from the speaker. To reattach the cover, line up the six holes on the cover with the six pegs on the speaker, and gently push the cover onto the speaker. Note: When removing the cover, be careful that you don’t touch the drive units, and don’t exert excessive force with any tools. Type.................2-way bass-reflex speaker system magnetic shielding type Drivers......2.2 cm (7/8 ”) balanced dome tweeter 8 cm (3.1 ”) cone woofer x2 Impedance ...................................................... 6 . Frequency response.......................60 Hz–35 kHz Nominal Input power ...................................40 W Maximum input power...............................120 W Sensitivity................................... 86 dB/2.83 V/m Crossover frequency....................................6 kHz Dimensions (with the stand) (W . H . D) .....236 (9.3 ”) . 1050 (41.3 ”) . 236 (9.3 ”) mm Weight........................................7.2 kg (15.9 lbs) * Specifications are subject to change without notice due to product improvements. This product mainly uses lead-free solder. Cet appareil utilise principalement de la soudure sans plomb. Dieses Produkt verwendet hauptsachlich bleifreies Lot. Este producto utiliza principalmente soldadura sin plomo. ©2004 All rights reserved. YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF....